Aastra DT412 User Manual Download

Page: 145 / 166

145

MD Evolution – Cordless DT412 / DT422 / DT432

Installation

This chapter describes how to connect and charge the battery of

your phone. You will also find procedures for installation and

maintenance of your phone.

Battery

The battery is a rechargeable battery placed on the back of the

phone.

Charging the battery

The battery requires charging when the

Battery

icon in the display

is half filled or empty.
Place the phone in the charger. A beep indicates connection with

the charger. The charging status is shown by the

Battery

icon in the

display. After approximately 1 hour the phone is fully charged,

indicated by a filled

Battery

icon. If the phone is switched off when

placed in the charger, it will start up automatically within 2 minutes.

Note:

If a call is connected when the phone is placed in the

charger, the call will be disconnected.

Remove the battery

The battery is fastened by a screw and two hooks. To remove the

battery on DT412 and DT422, use a small coin and turn the screw

to horizontal position. To remove the battery on DT432, use the

screwdriver delivered with the handset and turn the screw to

horizontal position. Remove the battery by pulling the screw. When

fastening the battery again the screw has to be in horizontal

position.

Summary of Contents for DT412






































































































































































Search results

Summary of Contents for DT412

Reviews:

Related manuals for DT412

Brands by name

Popular brands

Aastra DT412, User Manual

Search results

Summary of Contents for DT412

Reviews:

Related manuals for DT412

Brands by name

Popular brands