Aastra 6730I Administrator'S Manual Download | Manualshive

Page: 705 / 888

background image

Operational, Basic, and Advanced Parameters

41-001343-02 REV05 – 07.2014

A-99

RTP, Codec, DTMF Global Settings

Global Settings

Parameter

–

sip rtp port

Configuration Files

aastra.cfg, <model>.cfg, <mac>.cfg

Description

Indicates the port through which the RTP packets are sent. This value must specify the
beginning of the RTP port range on the gateway or router.

The RTP port is used for sending DTMF tones and for the audio stream. Your network
administrator may close some ports for security reasons. You may want to use this
parameter to send RTP data using a different port.

Note:

The phones support decoding and playing out DTMF tones sent in SIP INFO requests.
The following DTMF tones are supported:

•

Support signals 0-9, #, *

•

Support durations up to 5 seconds

Format

Integer

Default Value

3000

Range

Not Applicable

Example

sip rtp port: 3000

Parameter

–

sip use basic codecs

Configuration Files

aastra.cfg, <model>.cfg, <mac>.cfg

Description

Enables or disables basic codecs (G.711 u-Law, G.711 a-Law, G.729). Enabling this
parameter allows the IP phone to use the basic Codecs when sending/receiving RTP
packets.

Format

Boolean

Default Value

0

Range

0 - Disable
1 - Enable

Example

sip use basic codecs: 1

Parameter

–

sip amr codec payload format

Configuration Files

aastra.cfg, <model>.cfg <mac>.cfg

Description

Specifies the payload format for the AMR/AMR-WB codec.

Format

Integer

Default Value

0

Range

0-2

0 (Enable bandwidth efficient mode per RFC, no octet-aligned header is in the INVITE
SDP [default]).

1 (Enable octet-aligned mode and add octet-align:1 in SDP,
negotiate mode for incoming calls).

2 (Disable octet-aligned mode and add octet-align:0 in SDP,
negotiate mode for incoming calls).

Example

sip amr codec payload format: 1

«
...
703
704
705
706
707
...
»

Summary of Contents for 6730I

























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6730I

Brand: Samsung Pages: 252

Galaxy S20 FE 5G

Brand: Samsung Pages: 19

Galaxy S Epic SPH-D700

Brand: Samsung Pages: 264

Galaxy S II Skyrocket SGH-i727

Brand: Samsung Pages: 206

Galaxy S Plus GT-I9001

Brand: Samsung Pages: 147

Brand: Samsung Pages: 48

Galaxy J7 Prime

Brand: Samsung Pages: 33

Brand: Samsung Pages: 32

Brand: Samsung Pages: 2

Brand: Samsung Pages: 11

Brand: Samsung Pages: 2

Brand: Samsung Pages: 65

Brand: Samsung Pages: 2

Galaxy Amp Prime 3

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 163

Brand: Samsung Pages: 10

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands