Aastra 6730I Page 189 Administrator'S Manual Download | Manualshive

Page: 189 / 888

background image

Network Settings

41-001343-02 REV05 – 07.2014

4-42

DSCP Range/VLAN Priority Mapping

DSCP bits in the ToS field of the IP header are set for RTP, RTCP, and SIP packets using either the default values or the values
configured via the "

tos sip

", "

tos rtp

", and "

tos rtcp

" parameters.

When the VLAN global configuration parameter, "

tagging enabled

" is set to

1

, VLAN priority for IP packets is mapped to

the DSCP value instead of a single priority for all packets. An administrator can also configure VLAN priority for non-IP
packets using the "

priority non-ip

" parameter.

Since the default DSCP settings for SIP, RTP, and RTCP are 26, 46, and 46 respectively, this results in corresponding default
VLAN priorities of 3 for SIP, 5 for RTP, and 5 for RTCP (based on the settings in the table

“DSCP Range/VLAN Priority Map-

).

You can change the default parameters by modifying just the DSCP values, just the VLAN priority values, or by modifying
all values.

LAN Port

vlan id

VLAN ID

tos priority map

SIP Priority

tos priority map

RTP Priority

tos priority map

RTCP Priority

PC Port

vlan id port 1

VLAN ID

QoS eth port 1 priority

Priority

Notes:

•

In order for the software to successfully maintain connectivity with a network using VLAN functionality, the IP phone
reboots if you modify the "

tagging enabled

" (

VLAN Enable

in the Web UI), "

vlan id

"

,

or

"

vlan id port 1

"

parameters.

•

Setting the LAN Port VLAN ID (

vlan id

) to 4095 and PC Port VLAN ID (

vlan id port 1

) to any ID from 1 to 4094 will allow

frames from the PC Port (containing a VLAN ID) to be untagged before being forwarded to the LAN Port and frames
from the LAN Port (without a VLAN ID) to be tagged with the configured VLAN ID before being forwarded to the PC
Port. For configuring this feature via the Phone UI and the Aastra Web UI, see

“Configuring VLAN (optional)”

. For configuring this feature using the configuration files, see Appendix A, the section,

“Virtual Local Area

Network (VLAN) Settings”

•

Alternatively setting the LAN Port VLAN ID (

vlan id

) to any ID from 1 to 4094 and PC Port VLAN ID (

vlan id port 1

) to

4095 will allow frames from the LAN Port (containing a VLAN ID) to be untagged before being forwarded to the PC
Port and frames from the PC Port (without a VLAN ID) to be tagged with the configured VLAN ID before being for-
warded to the LAN Port. For configuring this feature via the Phone UI and the Aastra Web UI, see

“Configuring VLAN

on

. For configuring this feature using the configuration files, see Appendix A, the section,

tual Local Area Network (VLAN) Settings”

.

Parameters in Configuration Files

Parameters in Aastra Web UI

«
...
187
188
189
190
191
...
»

Summary of Contents for 6730I

























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6730I

Brand: 3Com Pages: 118

CoreBuilder 3500

Brand: 3Com Pages: 92

Brand: Blackberry Pages: 17

Brand: Gplus Pages: 68

Brand: NGM Pages: 166

AdvanceCommunicator ATT3001A

Brand: AdvanceTec Pages: 8

Brand: Sigma Pages: 61

Brand: Lanix Pages: 21

Brand: Lava Pages: 39

Brand: Zte Pages: 49

Brand: Yezz Pages: 23

Brand: Yealink Pages: 2

Brand: Yealink Pages: 3

Brand: Yealink Pages: 7

Brand: Yealink Pages: 6

Brand: Yezz Pages: 148

Brand: Yealink Pages: 475

TigerVoIP SMCDSP-200

Brand: SMC Networks Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands