manualshive.com logo in svg

AAON RSMV ASM01686, Technical Manual

Share
Download
AAON RSMV ASM01686 Technical Manual Download Page 20

20

      RSMV Technical Guide

RSMV LCD SCREENS

Diagnostic Screens

Diagnostic Screens

Refer to the following map when navigating through the Diagnostic 

Screens. From the DIAGNSTC Screen, press 

<ENTER>

 to scroll 

through the screens.

DIAGNSTC

WDOG CNT 

#

WATCH DOG TIMER

Displays the number of times the board has been reset due to 

watchdog timer overflow.

PWER CNT 

#

POWER LOSS COUNT 

Displays the number of times the board has been

 

 reset due to power loss.

EEPROM:

HOLD 

DOWN 

TO 

LOAD

DEFAULTS 

SP-A VLT 

X.XX

SUCTION PRESSURE SENSOR VOLTAGE

Displays the current voltage of the Suction Pressure Sensor.

HP-A VLT 

X.XX

HEAD PRESSURE SENSOR VOLTAGE

Displays the current voltage of the Head Pressure Sensor.

BIN1 - BIN4 

ON/OFF

BINARY INPUTS #1 - #4

Displays the current status of each Binary Input.

TMP1 VLT 

X.XX

COIL TEMPERATURE SENSOR 1 VOLTAGE

Displays the current voltage of the 1st Coil Temperature Sensor.

TMP2 VLT 

X.XX

COIL TEMPERATURE SENSOR 2 VOLTAGE

Displays the current voltage of the 2nd Coil Temperature 

 

Sensor.

TMP5 VLT 

X.XX

TEMPERATURE SENSOR 5 VOLTAGE (NOT USED)

Summary of Contents for RSMV ASM01686

































Reviews:

No comments

Brands by name

Popular brands

Load more brands