manualshive.com logo in svg

AAON RSMD, Technical Manual

Share
Download
AAON RSMD Technical Manual Download Page 22

22

      RSMD Technical Guide

LCD SCREENS

Diagnostic Screens

BIN 1 - BIN 4 

ON/OFF

BINARY INPUTS #1 - #4

Displays the current status of each Binary Input.

TMP1 VLT 

X.XX

COIL TEMPERATURE SENSOR 1 VOLTAGE

Displays the current voltage of Coil Temperature Sensor 1.

TMP2 VLT 

X.XX

COIL TEMPERATURE SENSOR 2 VOLTAGE

Displays the current voltage of Coil Temperature Sensor 2.

TMP3 VLT 

X.XX

COIL TEMPERATURE SENSOR 3 VOLTAGE

Displays the current voltage of Coil Temperature Sensor 3.

FORCE MODE

ON/OFF

FORCE MODE

Displays the current status of Force Mode. Values are ON/OFF.

IF FORCE MODE IS ON, THE FOLLOWING 

SCREENS WILL APPEAR:

RLY 1-5 

ON/OFF

RELAYS 1-5 FORCE MODE

Press the 

<UP>

 or 

<DOWN>

 buttons to select ON or OFF for reach 

relay.

TRIAC 1 

ON/OFF

TRIAC 1

Displays the current status of Digital Compressor 1.

Values are ON/OFF.

TRIAC 2 

ON/OFF

TRIAC 1

Displays the current status of Digital Compressor 2.

Values are ON/OFF.

AOUT-1 V 
0.0-10.0 

vdc

CONDENSER SIGNAL 1 FORCE

0.0 to 10.0 = Active Force Mode

Press the 

<UP>

 or 

<DOWN>

 buttons to increase and decrease the 

value.

AOUT-2 V 

1.0-10.0 

vdc

CONDENSER SIGNAL 2 FORCE

0.0 to 10.0 = Active Force Mode

Press the 

<UP>

 or 

<DOWN>

 buttons to increase and decrease the 

value.

Summary of Contents for RSMD











































Reviews:

No comments

Brands by name

Popular brands

Load more brands