www.australianawning.group
1300 791 010
linxautomation.com.au
Linx
®
Spinner Sun/Wind Sensor
1. To wake the sensor up for the first time, press the
reset
button. The screen will come on after a few seconds.
Until this is done, the sensor will generally not operate.
2. Adjusting Sun settings
Warning: In most cases it is not recommended to use the sun settings, as automated and unattended
operation of awnings can lead to possibly undesired or dangerous operation.
To ignore sun operation, make sure sun settings are set to “0.0”
1. Tap ‘M” to bring up display if it is blank.
2. Press and hold “M” for about 2 seconds and the digits will start flashing along with the sun symbol.
3. Use the “UP” button to count up and the “A” button to count down. Holding either button will cause
the unit to count faster.
4. Each full digit is 1000 Lux. You can set up to 100,000 Lux.
3. Adjusting Wind settings
1. Tap ‘M” to bring up display if it is blank.
2. Press and hold “M” for about 2 seconds and the digits will start flashing along with the sun symbol
.
3. Tap “M” again and the Flag (wind symbol) will appear, and the digits will flash.
4. Use the “UP” button to count up and the “A” button to count down. Holding down either button will
cause the unit to count faster in that direction.
5. The numbers in the display are the actual wind speed you are setting, from 0.1 kmh to 180 kmh.
For a folding arm awning, a speed of between 15 – 25 kmh would be normal. Higher settings can be used
for Zip systems.
NOTE: once the wind has triggered the awning to retract, a zip system or guided awning will not react to
the sensor again for 8 minutes, but the remote will still work.
For folding arm awnings, neither the sensor nor the remote will work for 8 minutes.
Bi-directional mode
Uni-directional mode
Safety code (50 million times without repeat, high security)
Working current:
＜
20mA
Working temperature
：
-10
℃
~+60
℃
Working voltage: DC 3.7V
Radio frequency:
433.05~434.79MHz
Radio range: outdoor
＞
100
meters, indoor
＞
40
meters
Technical specification
1, Stable performance, wireless remote control, solar powered, Type-C charging.
2, Check the voltage once a day. When the voltage is lower than 2.7V, a small battery icon is displayed to indicate low voltage.
3, The sensor can be fixed to the wall with two screws.
4, Adjustable wind intensity range: 0~180Km/h; sunlight intensity range: 0~100Klux.
5, Once the wind intensity exceeds the setting level, the sensor will send signals to the motor automatically to close the awning
within 3S.
6, When the sunlight intensity exceeds the setting level continuously more than 2 minutes, the sensor will send signals to open
the awning and will not detect the sunlight intensity within 15 minutes; when the sunlight intensity hasn't less than the setting
level continuously more than 15 minutes, the sensor will send signals to close the awning.
7, The LCD display screen will be ON for 30S. The LCD screen will turn off after 30S without any press while the programming
keeps running at the background; Press any button(except reset button) to turn on the LCD screen for 30S.
Warning
DD118B
DD118B
E/ED
-type
tubular motor
DD1600H
Standard tubular motor
DD1538H or External
Receiver (Refer to
"Matchable Receiver")
DC1600
R-type tubular motor
Note: 1,Pls make sure that the wind-sun sensor have been paired to the receiver.
2,pls make sure when press UP button, the awning will be retracted.
Version: A/03
LCD
DD118B
Wind-sun Sensor Instruction
km/h
k l u x
LCD
Menu
Adjust
P2
UP
Reset
SUN:
WIND:
Matchable Motors And Emitters
Product Features
