background image

Quick Installation Guide

PCM-6890   Installation Guide    1

PCM-6890

Notice:

This guide is designed for experienced users to
setup the system within the shortest time.  For
detailed information, please always refer to the
electronic user's manual.

Safety Precautions

PCM-6890

          All-in-One Socket 370 Celeron Single Board Computer
         with LCD, Ethernet, Audio, & 4 COMs

Part no. 2007689000   1st Ed.   Printed in Taiwan   May 1999

Quick Installation Guide

Warning!

Always completely disconnect the power cord

from your chassis whenever you work with the

hardware. Do not make connections while the

power is on. Sensitive electronic components

can be damaged by sudden power surges. Only

experienced electronics personnel should open the

PC chassis.

Caution!

Always ground yourself to remove any static

charge before touching the CPU card. Modern

electronic devices are very sensitive to static

electric charges. As a safety precaution, use a

grounding wrist strap at all times. Place all

electronic components in a static-dissipative

surface or static-shielded bag when they are not

in the chassis.

PCM-6890

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for PCM-6890













Reviews: