manualshive.com logo in svg

A.R.C. Laser Nuvolas, User Manual

Share
Download
A.R.C. Laser Nuvolas User Manual Download Page 47

User Manual NUVOLAS 

April 2023

 

 

 

File: User Manual_NUVOLAS_rev3.docx

 

 

 

47 

10  Guidelines and manufcaturers declaration 

The NUVOLAS does not have essential performance 

10.1  Electromagnetic Emission 

 

The laser is intended for use in an environment as specified below. The customer or user of the laser 
should ensure that it is operated in such an environment. 

Immunity tests 

Compliance 

Electromagnetic environment - 

guideline 

RF-Emissions  

CISPR 11 

EN 55011 

Group 1/Class B 

The laser uses RF energy exclusively for its 

internal function. Hence, RF emission is very 

low and not likely to cause any interference in 

nearby electronic equipment 

RF- Emissions  

CISPR 11 

EN 55011 

Group 1/Class B 

The laser is only suitable for the environment 

in professional healthcare facilities. 

Harmonic emission 

IEC 61000-3-2 

Class A 

Voltage fluctuations/flicker 

IEC 61000-3-3 

Summary of Contents for Nuvolas

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands