A.O. Smith Innovo IR 12-160 Installation, User And Service Manual Download Page 51

Page: 51 / 96

8.8.3.3 Additional error signal

Note
The water heater has a relay contact that can be used when an error occurs. The relay
contact is potential–free (maximal 5 A).

Note
There is a 1 minute delay between the switching of the relay contact and the error
message on the display.

Install an additional error signal:
1.

Pull the power cable through the tulles.

Connect the cables to X1 and X2.

Install the cables in a pull relief under the electrical section.

8.8.4

Finalization

When all connections are made, install the cover on the water heater:
1.

Place the cover on the water heater.

Use a hex driver to tighten the screw at the front of the cover.

Fig. Install the cover

0312266_INNOVO_UKUK_

V5.1, 2022-07-12

Summary of Contents for Innovo IR 12-160

































































































Search results

Summary of Contents for Innovo IR 12-160

Reviews:

Related manuals for Innovo IR 12-160

Brands by name

Popular brands

A.O. Smith Innovo IR 12-160, Installation, User And Service Manual

Search results

Summary of Contents for Innovo IR 12-160

Reviews:

Related manuals for Innovo IR 12-160

Brands by name

Popular brands