A.O. Smith Innovo IR 12-160 Installation, User And Service Manual Download Page 20

Page: 20 / 96

3.1.2

Buttons

The 5 buttons on the operator panel give access to the menu of the water heater.

Button

Function

[ ]

Scroll up / Raise

[ ]

Scroll down / Lower

[ENTER]

Enter / Confirm

[RESET]

Reset / Cancel

[MENU]

Go to menu

3.1.3

LCD display

The LCD display shows 7 different symbols around the outer edge of the display and 3
characters in the center of the display. The characters represent parameters.

Fig. LCD display

1. Characters
2. Symbols

The symbols on the display show visual information about the status of the water heater.

Symbol

Explanation

Heat demand present

Water heater in operation

Water heater not in operation - ERROR

Frost protection is activated

Scroll through menu

Shown on the right side corners of the display

External ON mode is activated

Shown on the upper left side corner

User part

Summary of Contents for Innovo IR 12-160

































































































Search results

Summary of Contents for Innovo IR 12-160

Reviews:

Related manuals for Innovo IR 12-160

Brands by name

Popular brands

A.O. Smith Innovo IR 12-160, Installation, User And Service Manual

Search results

Summary of Contents for Innovo IR 12-160

Reviews:

Related manuals for Innovo IR 12-160

Brands by name

Popular brands