background image

3

then call your gas supplier or service agent.  Keep area clear
until a service call has been made.

At times you may not be able to smell an LP gas leak.  One cause
is odor fade, which is a loss of the chemical odorant that gives LP
gas its distinctive smell.  Another cause can be your physical
condition, such as having a cold or a diminishing sense of smell
with age.  For these reasons, the use of a propane gas detector
is recommended.

IF YOU EXPERIENCE AN OUT-OF-GAS SITUATION, DO NOT
TRY TO RELIGHT APPLIANCE YOURSELF.  Ask your LP delivery
person to relight pilots for you.  Only trained LP professionals
should conduct the required safety checks in accordance with
industry standards.

EXTENDED NON-USE PERIODS

 

WARNING

HYDROGEN GAS CAN BE PRODUCED IN A HOT WATER
SYSTEM SERVED BY THIS HEATER THAT HAS NOT BEEN
USED FOR A LONG PERIOD OF TIME (GENERALLY TWO
WEEKS OR MORE).  HYDROGEN GAS IS EXTREMELY
FLAMMABLE. 

 To reduce the risk of injury under these conditions,

it is recommended that the hot water faucet be opened for several
minutes at the kitchen sink before using any electrical appliance
connected to the hot water system.  If hydrogen is present, there
will probably be an unusual sound such as air escaping through
the pipe as the water begins to flow.  

THERE SHOULD BE NO

SMOKING OR OPEN FLAME NEAR THE FAUCET AT THE TIME
IT IS OPEN.

INSULATION BLANKETS

Insulation blankets available to the general public for external
use on gas water heaters are not approved for use on your
water heater.  The purpose of an insulation blanket is to reduce
the standby heat loss encountered with storage tank heaters.
Your water heater meets and exceeds the National Appliance
Energy Conservation Act standards with respect to insulation
and standby loss requirements, making an insulation blanket
unnecessary.

 

WARNING

Should you choose to apply an insulation blanket to this heater,
you should follow these instructions (See Figure 1 for
identification of components mentioned below).  Failure to follow
these instructions can restrict the air flow required for proper
combustion, potentially resulting in fire, asphyxiation, serious
personal injury or death.

Do not cover the outer door, thermostat or temperature &
pressure relief valve.

Do not allow insulation to come within 2 inches of dilution air
inlet on the blower to prevent blockage of the dilution air.

Do not allow insulation to come within 2" of the floor to prevent
blockage of combustion air flow to the burner.

Do not cover the instruction manual.  Keep it on the side of
the water heater or nearby for future reference.

Do  obtain new warning and instruction labels for placement
on the blanket directly over the existing labels.

Do inspect the insulation blanket frequently to make certain it
does not sag, thereby obstructing combustion air flow.

 GENERAL SAFETY INFORMATION

EXTERNAL DAMAGE

Do not operate the water heater until it has been fully checked
out by a qualified technician, if the water heater:

• Has been exposed to fire or damage.
• Displays evidence of sooting.
• Produces steam or unusually hot water.

If the water heater has been flooded it must be replaced.

CHEMICAL VAPOR CORROSION

 WARNING

CORROSION OF THE FLUEWAYS AND VENT SYSTEM MAY
OCCUR  IF AIR FOR COMBUSTION CONTAINS CERTAIN
CHEMICAL VAPORS.  SUCH CORROSION MAY RESULT IN
FAILURE AND RISK OF ASPHYXIATION.

Spray can propellants, cleaning solvents, refrigerator and air
conditioning refrigerants, swimming pool chemicals, calcium and
sodium chloride (water softener salt), waxes, and process
chemicals are typical compounds which are potentially corrosive.

Do not store products of this sort near the heater.  Also, air which
is brought in contact with the heater should not contain any of
these chemicals.  If necessary, uncontaminated air should be
obtained from remote or outside sources. The limited warranty is
voided when failure of water heater is due to a corrosive
atmosphere.  (Reference is made to the limited warranty for
complete terms and conditions).

IMPROPER COMBUSTION

 

WARNING

ATTIC AND/OR  EXHAUST  FANS  OPERATING  ON  THE
PREMISES WITH A WATER HEATER CAN RESULT IN CARBON
MONOXIDE POISONING AND DEATH.

OPERATION OF THESE FANS CAN PRODUCE A NEGATIVE
DRAFT IN THE AREA OF THE WATER HEATER PREVENTING
THE PRODUCTS OF COMBUSTION FROM EXHAUSTING
THROUGH THE VENT PIPE.

The venting of the water heater should be inspected by a qualified
service technician at the time of installation and periodically
thereafter to ensure a down-draft condition does not exist.

DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND
VENTILATING AIR.  ADEQUATE AIR FOR COMBUSTION AND
VENTILATION MUST BE PROVIDED FOR SAFE OPERATION.

LIQUID PETROLEUM MODELS

 

WARNING

Water heaters for propane or liquefied petroleum gas (LPG) are
different from natural gas models.  A natural gas heater will not
function safely on LP gas and no attempt should be made to
convert a heater from natural gas to LP gas.

LP gas must be used with great caution.  It is highly explosive
and heavier than air.  It collects first in the low areas making its
odor difficult to detect at nose level.  If LP gas is present or even
suspected, do not attempt to find the cause yourself.  Go to a
neighbor's house, leaving your doors open to ventilate the house,

Summary of Contents for GPSX-50L





















Reviews: