A.O. Smith GPS-75 Instruction Manual Download Page 1

Page: 1 / 36

Thank you for buying this energy efficient water heater. We

appreciate your confidence in our products.
You should thoroughly read this manual before installation and/or

operation of this water heater. Please pay particular attention

to the important safety and operating instructions as well as the

WARNINGS and CAUTIONS.

Instruction Manual

PRINTED 1010

197209-003

Keep thIs Manual In the pocKet on heater for future reference

whenever MaIntenance adjustMent or servIce Is requIred.

all technIcal and warrantY questIons:

SHOULD BE DIRECTED TO THE LOCAL DEALER FROM WHOM THE WATER HEATER WAS

PURCHASED. IF YOU ARE UNSUCCESSFUL, PLEASE WRITE TO THE COMPANY LISTED ON THE RATING PLATE ON THE WATER HEATER.

resIdentIal Gas water heaters

•

for Your safety

•

AN ODORANT IS ADDED TO THE GAS USED

BY THIS WATER HEATER.

Gas Models power vent Gps-75

wIth hot surface IGnItIon

500 Tennessee Waltz Parkway

Ashland City, TN 37015

www.hotwater.com

Low Lead Content

Summary of Contents for GPS-75





































Search results

Summary of Contents for GPS-75

Reviews:

Related manuals for GPS-75

Brands by name

Popular brands

A.O. Smith GPS-75, Instruction Manual

Search results

Summary of Contents for GPS-75

Reviews:

Related manuals for GPS-75

Brands by name

Popular brands