A.O. Smith DHE200 THRU 10 Instruction Manual Download Page 20

Page: 20 / 22

rEstorE faCtory dEfaults MEnu

This control system menu allows the user to restore most of the control system’s user settings to their factory default

settings.

user settings in the alarm output setup and display settings menus are unaffected by executing restore

factory defaults.

restore factory defaults

aCtIon

dIsplay

From the Main Menu use the Up/Down buttons to select (highlight in

black) the “Restore Factory Defaults” menu.

Press the Operational Button underneath “SELECT.” The Restore

Factory Defaults menu will be displayed.

From the Restore Factory Defaults menu press the Operational Button

underneath “YES.” The display will show text confirming the factory

default settings have been restored.

Press the Operational Button underneath “BACK” to exit the Restore

Factory Defaults menu.

Summary of Contents for DHE200 THRU 10























Search results

Summary of Contents for DHE200 THRU 10

Reviews:

Related manuals for DHE200 THRU 10

Brands by name

Popular brands

A.O. Smith DHE200 THRU 10, Instruction Manual

Search results

Summary of Contents for DHE200 THRU 10

Reviews:

Related manuals for DHE200 THRU 10

Brands by name

Popular brands