background image

A.H. Systems Model Active Monopole Antennas 

 

 

 

 

©

 A.H. Systems inc

 

REV E 

12

 

 

FAQ’s 

 

Q: Is your output connector bonded to the network case per MIL-STD 461F/G?

 

A: The signal output connector is bonded to the antenna matching network case.

 

 

Q: The product page states that the antenna includes an 18” ground plane but the 
standard I’m testing to requires at least a 60cm ground plane?

 

A: Our standard monopole antennas comes with an 18” ground plane. A 24” ground 
plane is also available and typically in stock.

 

 

Q: What is the ECSM calibration?

 

A: ECSM stands for equivalent capacitance substitution method and it’s a calibration 
method  that  measures  the  insertion  loss  of  the  matching  unit  with  an  equivalent 
antenna fixture (our model ECF-12K).

 

 

Q: Can the active monopole antennas be used for transmitting applications?

 

A:  No,  the  active  monopole  antennas  are  a  receive  only  antenna.  Any  attempt  to 
transmit power with damage the antenna.

 

 

Q: My telescoping rod has a BNC connector; do you still carry this part?

 

A: Yes, the telescoping rod with a BNC connector (P/N 2337-1) is for our older active 
monopole  antennas.    All  new  active  monopole  antennas  have  been  re-designed  to 
accept a telescoping rod with a 1/4-20 thread instead of a BNC connector. This new 
connection makes for a better electrical performance as well as an improved rugged 
design.

 

 

Q: Can I use a different element length?

 

A: Yes, however calibration results were based on a 41” (1.04 Meter) element length 
and  they  will  not  be  valid  for  different  lengths.  Please  contact  our  calibration 
department for a custom calibration of the active monopole with a different element 
length.

 

 

Q: What type of battery is included with the active monopole antennas?

 

A: The active monopole antenna has a 12VDC NiMH 2000mAh battery assembly (P/N 
2351-3).

 

 

Q: How long does it take to charge the batteries?

 

A:  Every  hour  of  charge  will  result  in  two hours  of  operation  for  up  to  10  hours  of 
charging. Charging for up to 24 hours will not damage the battery.

 

 

Q: What is the lifetime of the battery pack?

 

A:  That  will  depend  on  the  amount  of  usage  (charge/discharge  cycles).  A  typical 
battery pack will last 3 to 5 years

 

 
 
 

Summary of Contents for SAS-550-1B















Reviews: