3onedata MES600 Series User Manual Download Page 23

Page: 23 / 76

Industrial Ethernet Switch User Manual

3onedata proprietary and confidential



Optical port rate mode, duplex mode, flow control may not be installed. It defaults to full
duplex, flow control closed. This feature is consistent with the port status of the port
information.

4.2 Bandwidth management

4.2.1 Bandwidth Management

Bandwidth management mainly refers to limit the data’s egress and ingress

bandwidth to save the network sources.

Click [port setting/bandwidth management] and enter into the following interface.

Egress Bandwidth and Ingress Bandwidth Configuration:

“----” stands for no limitation for the speed, the others are corresponding speed.

As shown in following figure, the forcible egress rate of Port 5 is 50Mbps. Only need to

select 50Mbps in egress rate setting of Port 5. The bandwidth of Port 5 as receiver is

still 80Mbps, but the forcible egress bandwidth of Port 5 is 50Mbps.

4.3 Storm Suppression

Broadcast storm is the accumulation of broadcast and multicast traffic on a computer

network. Extreme amounts of broadcast traffic constitute a broadcast storm. A

broadcast storm can consume sufficient network resources so as to render the

network unable to transport normal traffic.

Summary of Contents for MES600 Series













































































Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands

3onedata MES600 Series, User Manual

Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands