3onedata MES600 Series User Manual Download Page 10

Page: 10 / 76

Industrial Ethernet Switch User Manual

3onedata proprietary and confidential

1.3 Log in the Web Configuration Interface

Operation Steps

Run the computer browser.

Step 1

On the browser's address bar, type in the switch addresses "http://192.168.1.254 ".

Step 2

Click the “Enter” key.

Step 3

Pop-up a window as the figure below, enter the user name and password on the login

Step 4

window.

Notes:



The default username and password are “admin12345”, please strictly distinguish capital
and small letter while entering.



Default username and password have the administrator privileges.



WebServer will provide 3 times opportunities to enter username and password. If enter
the error information for 3 times, the browser will display a "Access denied" to reject
access message. Refresh the page and try again.

Click "OK".

Step 5

End.

Step 6

After login in successfully, user can configure relative parameters and information

according to demands.

Notes:

After login in the device, modify the switch IP address for usage convenience.

Summary of Contents for MES600 Series













































































Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands

3onedata MES600 Series, User Manual

Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands