manualshive.com logo in svg

3onedata IES716-2GS, User Manual, Page: 25 / 54

Share
Download
3onedata IES716-2GS User Manual Download Page 25

                                                                                                                      User manual  

 

 

Page 25 

 

（

Figure 6.4.6

）

 

 

1. Must configure the VLAN of 802.1q at first, then open IGMP Snooping function 

2. Please do not open more IGMP snooping,  waste source.

 

6.4.3 Static Multicast FWD 

The device provides the function of static MAC address forwarding. The destination address includes 

the data packets with static MAC address which will be transferred to the appointed port. Embedded 

forwarding address list in the switch chip can learn and support 2,000 MAC addresses and 16 multicast 

forwarding ports list. Static MAC address  carry out transmit function,  it did not accept the arrangement 

of  aging. 

 

 

（

Figure 6.4.7

）

 

 

Button [Add/Edit], [Delete] were used for  add/delete static Multicast MAC address.  Join port is 

used to choice the  transmit port of  static MAC address,  can  point to 1 or more  transmit port. 

Knock[Add], [Delete], static MAC address will be  updated. For example, add MAC address “01-00-00-
00-00-01-01”  member is  port 1, 2

，

3

，

4. Multicast MAC address is 1 of highest byte’s low byte. All 

Summary of Contents for IES716-2GS























































Reviews:

No comments