3onedata IES716-2GS User Manual Download Page 15

Page: 15 / 54

User manual

Page 15

Menu Introduction:

Main Menu

Tag

Function

System Status

System information

Display device information and port information such

as software version, IP address, etc.

Port Configuration

Port settings

Display and configure information of each port: such as

connection status, configuration modes, flow status etc.

Bandwidth

management

Set the maximum rate of the input/output packets for

port.

L2 feature

VLAN

Displays the current list of 802.1Q VLAN, configure and

manage 802.1Q VLAN.

IGMP snooping

Display port-based VLAN list, and to configure and

manage port-based VLAN.

Static Multicast

Configure the static multicast MAC address and its

corresponding port.

QOS

QoS classification

Configure the the QOS queue mode, QOS

implementation and port default priority.

Cos Mapping

Configure the meaning of COS value.

Dscp

Configure the DSCP priority.

Redundancy

Port Trunking

Configure port trunking group.

Rapid Ring

Configure the rapid ring network port and type.

RSTP

Configure the parameters of RSTP.

Access control

Configure different permissions for the user name and

password.

Remote

Monitoring

SNMP

Relay Warning

Port Statistics

Frame statistics

Diagnosis

Mirror

Configure the mirror port and mirrored port.

Basic Settings

System Identification

Device IP, gateway, DNS and other information.

System Log

Log information.

System File update

Software upgrade, acquire, preserve or restore the

switch configuration.

Web Timeout Treatment

The system timeout will cancel the login if the user did not login for a long time (The configuration

of this login will be remained in the Web interface).

If user doesn't operate the Web interface for a long time, The system will be canceled this login.(but configuration

change made in this login will be saved in Web configuration interface.). If the user wants to do any operating on

Web configuration interface again, the system will remind user and returns to the login dialog box. Users need to

6.2 System status

Device information

Summary of Contents for IES716-2GS























































Search results

Summary of Contents for IES716-2GS

Reviews:

3onedata IES716-2GS, User Manual, Page: 15 / 54

Search results

Summary of Contents for IES716-2GS

Reviews: