3M SST Manual Download Page 54

Page: 54 / 90

44 • Ch. 4 Preventive Maintenance

75-0302-1450-8, Version 1

SST Transport and Burster Mechanism Manual

Warning! Do not use petroleum-based lubrication on any part, especially near the rubber

rollers. This will damage the rubber.

18. Reinstall the Burster. Refer to

Chapter 3: Burster Mechanism

for instruction on reinstall-

ing the Burster.

19. Restore power to the unit.

20. Load tickets in the Burster. If you have a Single Infeed Burster tickets should load auto-

matically. If you have a Dual Infeed Burster carefully feed the ticket into the ticket infeed

slot and into the bottom roller. You should feel the tickets provide resistance or “kick

back.” Otherwise, press the red Reset Button on the SST CPU Board and load tickets

again.

21. Issue tickets from the SST Transport. Save the issued tickets for verification later at an

SST Validator.

Summary of Contents for SST



























































































Search results

Summary of Contents for SST

Reviews:

Related manuals for SST

Brands by name

Popular brands

3M SST, Manual

Search results

Summary of Contents for SST

Reviews:

Related manuals for SST

Brands by name

Popular brands