3M Flexiguard 8560012 User Instruction Manual Download Page 1

© 3M 2017

Form: 5903683 Rev: D

12

Figure 1 - Flexiguard™ Counterweight Rail Fall Arrest System (FAS)

A

A

B

B

D

E

E

C

I

D

F

F

F

G

G

H

H

J

J

K

K

L

L

L

L

A

Primary Forklift Pockets

B

Alternate Forklift Pockets

C

Counterweight Base

D

Slope Indicator

E

Vertical Support Beams

F

Rail Supports

G

Glide Rail & Glide 4-Wheeled Trolley

H

Material Lifting Rings

I

Counterweight

J

Tie-back Supports

K

Cross Members

L

Leveling Feet

WARNING:

 This product is part of a personal fall arrest system

1

. The user

 

or rescuer

2

 must read and follow the manufacturer’s 

instructions for each component or part of the complete system. These instructions must be provided to the user/rescuer utilizing 

this equipment. The user/rescuer must read and understand these instructions or have them explained to them before using this 

equipment. Manufacturer’s instructions must be followed for proper use and maintenance of this product. Alterations or misuse 

of this product or failure to follow instructions may result in serious injury or death. If this product is resold outside the original 

country of destination, the re-seller must provide these instructions in the language of the country in which the product will be 

used.

IMPORTANT:

 If you have questions about the use, care, or suitability of this equipment for your application, contact Capital 

Safety.

IMPORTANT:

 Before using this equipment, record the product identification information from the ID label in the Inspection and 

Maintenance Log at the back of this manual.

1  Fall Arrest System:

 A system that prevents the worker from colliding with an obstruction or lower level by arresting a fall.

2 Rescuer:

 Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.

Counterweight Rail

Fall Arrest System

Model Number: 

8560012, 8560024, 8560025, 8560124

 USER INSTRUCTION MANUAL

CEN/TS 16415: 2013

CE Type Test

No. 0086

BSI Product Services

Kitemark Court

Davy Avenue

Knowlhill, Milton Keynes

MK5 8PP, UK

CE Production Quality Control

No. 0086

BSI Product Services

Kitemark Court

Davy Avenue

Knowlhill, Milton Keynes

MK5 8PP, UK

Summary of Contents for Flexiguard 8560012













Reviews: