background image

SAFETY INFORMATION

Read, understand, and follow all safety information contained in these instructions prior to installation and use of the CFSBWF Series Backwash 
Filtration Systems. Retain these instructions for future reference.

Intended use:

The CFSBWF Series Backwash Filtration Systems are intended for use in reducing undesirable aesthetics in water in commercial establishments and 
have not been evaluated for other uses. The system is intended for indoor installations near the entry point of a water line, and must be installed by 
qualifi ed professional installers according to these installation instructions.

EXPLANATION OF SIGNAL WORD CONSEQUENCES

 WARNING

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury and/or 
property damage.

 CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or 
property damage.

CAUTION

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result in property damage.

 WARNING

To reduce the risk associated with choking: 

• 

Do not

 allow children under 3 years of age to have access to small parts during the installation of this product.

To reduce the risk associated with ingestion of contaminants:

• 

Do not 

use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

To reduce the risk of physical injury: 

•  Shut off inlet water supply and depressurize system as shown in manual prior to service.

To reduce the risk associated with a hazardous voltage:

•  If the electrical system requires use of the cold water system as an electrical safety ground, a jumper must be used to ensure a suffi cient ground connection 

across the fi lter installation piping — refer installation to qualifi ed personnel.

• 

Do not

 use the system if the power cord is damaged — contact qualifi ed service personnel for repair.

To reduce the risk associated with back strain due to the heavy weight of the various system components:

•  Follow safe lifting procedures.

 CAUTION

To reduce the risk associated with skin, eye, and respiratory tract irritation from dust from fi lter media during installation:

•  Gravel and several types of fi lter media may be used in this product, depending upon the application. During installation, dust may cause irritation to skin, 

eyes, and respiratory tract, and may affect lungs.

•  Utilize a NIOSH-approved dust fi lter mask and appropriate eye protection when handling and pouring gravel and fi lter media.
•  To request an MSDS relating to the media for this product, call 203-238-8965 or go to www.3M.com , select country, and use the search engine to search 

MSDS.  For emergencies, call 800-364-3577 or 651-737-6501 (24 hours).

Summary of Contents for CFS101BWF





















Reviews: