3M 9800 Service Manual Download Page 34 | Manualshive

Page: 34 / 52

3M 9800 Service Manual Download Page 34

3M

Overhead Projector 9800 Series

Section 5 – Disassembly/Reassembly

5-9

9800 Service Manual

3M 1996

5-3-3. How to Replace the Condenser Lens

Caution

Handle the lens carefully to prevent chipping or
scratching the surface during installation.

1. Remove the hot mirror. Section 5-3-2.

2. Unscrew four retaining screws securing condenser

lens to bracket. Figure 5-17.

3. Carefully remove two metal retainers and

condenser lens.

4. Reassemble in reverse order.

Figure 5-17. Condenser Lens

Important

Install the condenser lens with the bowed
side facing the hot mirror. Figure 5-18.

ÉÉÉÉÉÉÉ

Bowed side toward hot mirror

Hot Mirror

Condenser Lens

9800-97I

Figure 5-18. Condenser Lens Orientation

5-3-4. How to Replace the Lamp Socket

!

Unplug projector power cord before performing
any maintenance to electrical components.

1. Unplug power cord from electrical outlet.

2. Open the top cover.

1. Release the spring clip and open the top assembly.

Figure 5-15.

2. Remove lamps from lamp socket.

3. Unscrew two retaining screws securing lamp

socket. Figure 5-19.

4. Disconnect lamp socket wire connectors from the

control module. Figure 5-13.

5. Reassemble in reverse order.

Figure 5-19. Lamp Socket

«
...
32
33
34
35
36
...
»

Summary of Contents for 9800





















































Reviews:

No comments