3M 3M-Matic Accuglide 21700 Instructions And Parts List Download

Page: 20 / 52

NA - ENG

June 2017

3M-Matic

™

Accuglide NPH - 2 Inch Taping Head - Type 21700

Page 12

(maintenance

continued

on next page.)

Maintenance

The

NPH 2 Inch Taping Head

will perform

best when it receives routine maintenance

and cleaning. Taping head components that

fail or wear excessively should be promptly

repaired or replaced to prevent damage to

other portions of the head or to the product.

Blade Replacement

, Upper and Lower

Taping Heads

(Figure 4-1).

1. Loosen, but do not remove, the blade

screws (A). Remove and discard old blade.
2. Mount the new blade (B) in the same

position as the blade that was removed.
3. Bottom the blade slots against the screws.

(This will position the blade at the correct
angle.) Tighten the blade screws to

secure

the

blade.

Note

–

Check the blade position to insure

proper clearance between blade

and guard by slowly pivoting the

blade guard back.

Blade Guard

The blade guard covers the blade whenever

a box is not being taped. Periodically check

to be sure the blade guard is functioning

properly and returning to cover the blade.

Replace any defective parts.

Blade Oiler Pad

To reduce adhesive build-up, the taping

heads are equipped with a factory pre-

lubricated felt oiler pad that provides a

lm of oil on the cutting edge of the blade.

Blade maintainance should include keeping

the felt oiler pad saturated with SAE #30

non-detergent

oil.

Should tape adhesive build-up occur on

blade, carefully wipe clean with an oily

cloth.

• To reduce the risk associated with

sharp blade hazards:

- Keep hands and

ngers away from

tape cuto

blades under orange blade

guards. The blades are extremely sharp.

Warning

• To reduce the risk associated with
shear, pinch, and entanglement hazards

- Turn air and electrical supplies o

on associated equipment before

  performing any adjustments, mainte-
  nance, or servicing the taping heads
-  Never attempt to work on the taping

head or load tape while the box drive

system is running

Warning

Figure 4-1 Blade Replacement

Blade

Holder

Blade

Screws

(A)

Blade

(B)

Summary of Contents for 3M-Matic Accuglide 21700





















































Search results

Summary of Contents for 3M-Matic Accuglide 21700

Reviews:

Related manuals for 3M-Matic Accuglide 21700

Brands by name

Popular brands

3M 3M-Matic Accuglide 21700, Instructions And Parts List

Search results

Summary of Contents for 3M-Matic Accuglide 21700

Reviews:

Related manuals for 3M-Matic Accuglide 21700

Brands by name

Popular brands