manualshive.com logo in svg

3DHISTECH PANNORAMIC SCAN RX 1.1, User Manual, Page: 58 / 165

Share
Download
3DHISTECH PANNORAMIC SCAN RX 1.1 User Manual Download Page 58

PANNORAMIC® SCAN RX 1.1 

SCANNING MODES AND SETTINGS 

 

NOVEMBER 18, 2021 

57

 

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

 

5

 

Scanning Modes and Settings

 

After microscope initialization, if FL HW option is provided, you can select from the 
following two modes:

 

•

 

Brightfield scanning mode

 (See chapter 

5.1 Brightfield Scanning Mode

 for more 

information.

)

 

•

 

Fluorescence scanning mode

 (See chapter 

5.2 Fluorescence Microscope Mode

 for more 

information.)

 

•

 

Option modes

 

o

 

 Microscope mode 

(available only if 

Services

 or 

Settings

 mode is active)

 

o

 

 Settings

 (See chapter 

6 Settings and Service

s

 for more information.)

 

o

 

 Services

 (See chapter 

6 Settings and Services

 

for more information.) 

In accordance with the selected mode, the 

Profile Settings Panel 

and the 

Microscope 

Control Panel 

views are modified. 

5.1

 

Brightfield scanning mode

 

Microscope View consist of three different chapters:

 

•

 

Main functions

: Located at below the window header, these functions are identical in 

both modes.

 

•

 

Profile Settings panel

: Profile settings containing parameters used for scanning

 

•

 

Microscope Control Panel

: Live microscope movement functions

 

 

Figure 32. Main window of Brightfield Microscope mode 

Summary of Contents for PANNORAMIC SCAN RX 1.1






































































































































































Reviews:

No comments