manualshive.com logo in svg

3DHISTECH PANNORAMIC SCAN RX 1.1, User Manual, Page: 150 / 165

Share
Download
3DHISTECH PANNORAMIC SCAN RX 1.1 User Manual Download Page 150

PANNORAMIC® SCAN RX 1.1 

TROUBLESHOOTING AND MAINTENANCE 

 

NOVEMBER 18, 2021 

149

 

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

 

9.3.1

 

Cleaning the device 

•

 

Before cleaning, switch off the device and pull the plug out.

 

•

 

Do not let liquid penetrate into the system.

 

•

 

To clean liquid from the device, use a lint-free cotton cloth. You can moisten the cloth 
with water.

 

•

 

To clean greasy surfaces, it is recommended to apply 

soapy water 

on a piece of lint-free 

cotton cloth and gently rub the surface.

 

9.3.2

 

Cleaning the magazines

 

NEVER

 clean the magazines with 

Xylene

 because it might harm the plastic. We recommend 

applying 

Isopropanol

 on a piece of lint-free cotton cloth and gently rub the surface instead. 

In case the magazine is damaged, use either order a new one, as inserting a deteriorated 
magazine could lead into unsafe loading of slides.

 

9.3.3

 

Preventive maintenance 

To prevent fungus growth

 

•

 

Do not leave the equipment in an unconditioned environment with a storage 
temperature above 60°C (140°F) or below 0°C (32°F), which may damage the equipment.

 

•

 

Maximum operating temperature is 35°C (95°F) with a relative humidity of less than 75%.

 

•

 

Install it in a room with proper air ventilation.

 

•

 

Do not let dust or fingerprints remain on optical surfaces.

 

9.4

 

Troubleshooting 

This chapter describes the most common troubleshooting solutions for the Pannoramic® 
SCAN RX product. If any problem arises that does not have solution in this manual, contact 
3DHISTECH service support at 

[email protected]

. 

The product does not start.

 

•

 

Power supply is interrupted.

 

1.

 

Make sure that the 24V external power supply is on.

 

2.

 

Check cable connections.

 

Pannoramic® Scanner Software for Research control software has stopped.

 

•

 

Slide jammed

 

1.

 

Exit control software. 

Summary of Contents for PANNORAMIC SCAN RX 1.1






































































































































































Reviews:

No comments