3D Systems Viper Pro SLA User Manual Download Page 97

Page: 97 / 121

www.3dsystems.com

m a i n t e n a n c e

user

’

s manual

Maintenance

Damage

If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.

Damage

Do not remove any outer panels when cleaning the Viper Pro SLA system.
Panels must be removed only by a qualified 3D Systems Customer Support
Representative.

Viper Pro SLA System Cleaning and Decontamination

Clean the Viper Pro’s inner and outer surfaces and windows periodically as described in the
following paragraphs.

Viper Pro SLA System Surfaces

Clean the Viper Pro SLA system’s outer surfaces as needed following these guidelines:

Dust Removal

Remove dust from the outer surfaces of the Viper Pro SLA system by wiping with a clean, dry,
lint-free cloth.

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands