3D Systems Viper Pro SLA User Manual Download

Page: 74 / 121

www.3dsystems.com

b u i l d w i n d o w

user

’

s manual

Recoat

Build

Recoat

displays the recoat parameter values as defined when

the build file was created by the 3DManage™ Software.

Distance:

Displays elevator dip distance in units (inch/mm) defined

by the .bff file.

Pre Dip:

Displays the time delay in seconds between the elevator dip

and the leveling operations.

Z Wait:

Displays the time delay in seconds between the recoating

and the drawing operations.

Sweeps:

Displays the number of recoater blade sweeps

per layer

during the recoating process.

Sweep:

Displays the percent blade gap.

Velocity:

Displays the velocity of the sweeping motion in units

(inch/mm) defined by the .bff file.

70696 Revision 1C 27-Aug-08

Summary of Contents for Viper Pro SLA


























































































































Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands

3D Systems Viper Pro SLA, User Manual

Search results

Summary of Contents for Viper Pro SLA

Reviews:

Related manuals for Viper Pro SLA

Brands by name

Popular brands