manualshive.com logo in svg

3D Systems PostCure 1050, User Manual, Page: 65 / 68

Share
Download
3D Systems PostCure 1050 User Manual Download Page 65

9

  POSTCURE 1050 SERVICE AND SUPPORT

Note: Whenever you have a problem or a question it is best to contact your reseller directly first.

If the certified partner cannot help you then there is a Customer Support Hotline you can use. If you and your reseller are

unable to recover from a printer error, or if you need to contact us for another problem, you may contact our Customer

Support Hotline. Before you call Customer Support with a problem or question, please make sure that you have the following

information:
• The serial number of your machine, which is printed on the product label.
• A brief description of the problem, including the exact error message.
• The steps you took that produced the error, if those steps are apparent to you
• When the problem occurred; for example, when you started a curing cycle.
• Relevant pictures/videos

Customer Support Hotline
Please contact your Customer Support Hotline at one of the following numbers:
• US and Canada: 888-598-1438
• UK and EMEA: +44 1442 279883
• International: +1 803-326-3930

General
Printer service procedures must be performed only by a 3D Systems-certified service technician unless this guide explicitly

states otherwise. If your printer system needs service, contact 3D Systems Technical Support at the following numbers:
• In the United States or Canada, call 800-793-3669
• In Europe, call +49-6151-357357
You can also contact your local 3D Systems representative.
3D Systems’ support portal is located at 

http://www.3dsystems.com/support

For safety data sheets of Figure 4 materials, go to 

http://www.3dsystems.com/support/materials/msds

3D Systems, Inc.

62

p/n 40-D177, Rev. A

Summary of Contents for PostCure 1050





































































Reviews:

No comments