3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 318 / 344

background image

318

A

PPENDIX

D: D

OWNGRADING

VCX S

ERVER

S

OFTWARE

The downgrade procedure does not remove VCX version 7.0 software
from your VCX system.

If you have configured a VCX server running version 7.0 software for
RAID operation, you cannot downgrade that server to version 6.0
software. VCX servers running software versions prior to the 7.0 release
do not support RAID configuration. If a VCX server enabled for RAID
operation must be downgraded to a software version prior to 7.0, the
server must be rebuilt. Contact your 3Com representative.

Downgrading a

Single-Site System

This procedure describes how to downgrade VCX single-site systems.
Single-site VCX systems can have either two servers or four servers.

■

In a two-server configuration, each server runs IP Telephony server
software and IP Messaging server software.

The downgrade steps described in the following sections must be
performed on each server.

■

In a four-server configuration, one pair of servers runs IP Telephony
server software; the second pair of servers runs IP Messaging server
software.

The downgrade steps described in the following sections must be
performed on each server running IP Telephony server software. For
servers running IP Messaging server software, the database
maintenance steps are not required.

Switch VCX Version

To switch the VCX version, perform the steps in this section on each
server in the single-site system.

■

In a two-server configuration, perform the steps first on the primary
server and then on the secondary server.

■

In a four-server configuration, perform the steps first on the primary IP
Telephony server and then on the secondary IP Telephony server. Then
perform the steps first on the primary IP Messaging server and then on
the secondary IP Messaging server.

1

Log in to the server as

root

user.

2

Enter the following command:

vcx-switchversion --manual 6.x

For example, to downgrade to VCX version 6.0.2.c, enter:

vcx-switchversion --manual 6.0.2c

«
...
316
317
318
319
320
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Uniden Pages: 16

Brand: Haier Pages: 57

Brand: Nec Casio Pages: 390

Brand: Audiovox Pages: 13

Brand: iBall Pages: 17

Capsat TT-3060A

Brand: Thrane&Thrane Pages: 182

Brand: Pantech Pages: 90

Brand: TCM Mobile Pages: 37

Brand: Wistec Pages: 60

Brand: SouthernLINC Pages: 63

Brand: Sony Ericsson Pages: 2

Brand: ORA Pages: 26

Brand: Pantech Wireless Pages: 71

Polycom VVX 150

Brand: CBTS Pages: 2

SUNBURST SGH-A697 Series

Brand: Samsung Pages: 185

Brand: Samsung Pages: 132

Brand: Samsung Pages: 133

Brand: Bosch Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands