3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 229 / 344

background image

Upgrading a Single-Site System With Four Servers

229

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

y

c). If the link does not point to the new version, wait a few

minutes and reenter the command. This could take several minutes and it
is important the link pointer is correct before proceeding.

Example Output

/opt/3com/VCX -> /opt/3com/VCX.7.1.

y

c

Upgrading the

Secondary IP

Telephony Server

Follow the steps in this section to upgrade the secondary IP Telephony
server.

1

To start the upgrade process, enter these commands on the secondary IP
Telephony server:

cd /opt/installtemp

tar xvf vcx-softswitch-7.1.

y

c.tar

cd upgrade-7.1.

y

c

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.1.

y

c is now available -------------------

2

Switch to the new software version by entering the following command:

vcx-switchversion 7.1.

y

c

The system displays several status messages and then reboots. After the
the reboot process has been completed, the system starts VCX 7.1.

y

IP

Telephony services.

3

After the system has completed the restart process, verify that the
upgrade has occurred by entering this command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

y

c). If the link does not point to the new version, wait a few

minutes and reenter the command. This could take several minutes and it
is important the link pointer is correct before proceeding.

«
...
227
228
229
230
231
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Panasonic Pages: 100

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 112

Brand: Yealink Pages: 3

Brand: HTC Pages: 80

Brand: Gigaset Pages: 27

Brand: TCL Pages: 61

Yealink SIP-T20P

Brand: Yealink Pages: 2

Brand: Alcatel Pages: 53

Brand: Rath Pages: 9

Brand: Indicom Pages: 37

Brand: TIPTEL Pages: 52

Brand: Vertu Pages: 73

Soundpoint IP550

Brand: Polycom Pages: 4

Brand: Salora Pages: 33

Brand: T-Mobile Pages: 59

Brand: STK Professional Audio Pages: 13

Brand: Pantech Wireless Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands