3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 219 / 344

background image

Upgrading a Single-Site System With Two Servers

219

Supported on:

■

Single-site systems with four servers

■

Multi-site systems that include servers at regional offices and
servers at branch offices that use global or local IP Messaging

■

A pair of Global Voicemail Central Servers (GVCS) to enable Global
Voicemail Integration on an entire IP Messaging system

A GVCS coordinates mailbox creation and mailbox updates on
regional and branch office IP Messaging servers. If you want to
enable Global Voicemail Integration on a 7.1 system, you must
install IP Messaging software on a GVCS, and then set up the
GVCS through the IP Messaging administrator configuration
interface. Next, run

vcx-reconfigure

on regional

and branch office IP Messaging servers to enable Global Voicemail
Integration. Refer to the

IP Messaging Module Operations and

System Administration Guide

for more information and for

configuration options.

■

Call server software

Supported on multi-site systems that include servers at regional offices
with or without branch offices

■

Call Records server software

Supported on multi-site systems installed on a single server for
regional offices with or without branch offices

■

Authentication and Directory server software

Supported on multi-site systems that include servers at regional offices
with or without branch offices

You should upgrade each server from a locally attached console. The
upgrade procedure includes a reboot of each upgraded server. If you
perform an upgrade remotely (using a secure shell client, for example),
you will be logged out when the reboot occurs. When you log back in, it
may not be apparent that the upgrade has completed. If you enter
commands before the upgrade has finished, the upgrade will fail.

Upgrading a
Single-Site System
With Two Servers

Single-site VCX systems can have either two servers or four servers.

■

In a two-server configuration, each server runs IP Telephony server
software and IP Messaging server software.

«
...
217
218
219
220
221
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Yealink Pages: 2

Brand: KALLIOPE PBX Pages: 2

Yealink SIP-T48G

Brand: Yealink Pages: 9

Yealink SIP-T42G

Brand: Yealink Pages: 2

Brand: Watchguard Pages: 12

Brand: Blu Pages: 20

Orion Mini S350

Brand: Posh Pages: 20

Brand: Fortinet Pages: 28

Brand: Ericsson Pages: 75

Brand: EMPORIA Pages: 2

Brand: Pantech Pages: 77

Brand: HTC Pages: 16

Brand: BarcodeYes Pages: 12

Brand: King Pigeon Communcation Pages: 15

Brand: Emerson Pages: 114

Brand: Lava Pages: 25

Brand: Ice Mobile Pages: 24

Memory Stick Camera Application Version 1.0

Brand: Sony Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands