3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 182 / 344

background image

182

A

PPENDIX

A: U

PGRADING

VCX S

ERVER

S

OFTWARE

F

ROM

V7.0

TO

V7.1

Enable UPS monitoring? [N] :

If you do not have a UPS installed and enter

n

(or press

Enter

); the

remaining UPS configuration prompts are not displayed.

If you do have a UPS installed and enter

y

and see

Configuring UPS

for information on the subsequent UPS configuration

prompts.

5

After completing the Adhoc Conferencing and UPS Monitoring prompts,
the server reboots. When the reboot process has been completed, the
system starts VCX 7.1.

x

services.

6

After the system has completed the restart process, verify that the
upgrade has occurred by entering this command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

x

c). If the link does not point to the new version, wait a few

minutes and reenter the command. This could take several minutes and it
is important the link pointer is correct before proceeding.

Example Output

/opt/3com/VCX -> /opt/3com/VCX.7.1.

x

c

7

Stop the Authentication and Directory service by entering the following
commands:

cd /opt/3com/VCX/scripts/rc3.d

./S20vcxdata stop

Upgrading the

Primary IP Messaging

Server

Follow the steps in this section to upgrade the primary IP Messaging
server.

1

To start the upgrade process, enter these commands on the primary IP
Messaging server:

cd /opt/installtemp

tar xvf vcx-ipmsg-7.1.

x

c.tar

cd upgrade-7.1.xc

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

«
...
180
181
182
183
184
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: GAI-Tronics Pages: 32

Brand: Samsung Pages: 2

Brand: Samsung Pages: 62

Brand: Samsung Pages: 48

Brand: Samsung Pages: 33

Brand: Samsung Pages: 2

Focus S SGH-I937

Brand: Samsung Pages: 175

Brand: Samsung Pages: 2

Brand: Samsung Pages: 24

Brand: Samsung Pages: 2

Brand: Samsung Pages: 145

Brand: Samsung Pages: 167

Brand: Aastra Pages: 9

Brand: Wiko Pages: 56

Brand: Docomo Pages: 18

Brand: LIKUID Pages: 6

Brand: iBall Pages: 17

Brand: RATH MICROTECH Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands