3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 181 / 344

background image

Upgrading a Single-Site System With Four Servers

181

Upgrading the

Primary IP Telephony

Server

Follow the steps in this section to upgrade the primary IP Telephony
server.

1

To start the upgrade process, enter these commands on the primary IP
Telephony server:

cd /opt/installtemp

tar xvf vcx-softswitch-7.1.

x

c.tar

cd upgrade-7.1.

x

c

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.1.

x

c is now available -------------------

2

Switch to the new software version by entering the following command:

vcx-switchversion 7.1.

x

c

The system displays several status messages and provides prompts that
allow you enable Adhoc Conferencing and UPS Monitoring.

3

The Adhoc Conferencing prompt appears:

In order to support "ad-hoc" conferences with more than 3

participants, the Adhoc Conference Service is used. This

service should be enabled on this server, unless another

server dedicated to Adhoc Conferencing will be used instead.

If available, a separate server typically provides greater

capacity and may be shared among sites.

Use the Adhoc service on this server? (Y/N) [Y] :

If you want this server to act as a multi-caller (up to 6 callers)
conferencing server, enter

y

. If not, enter

n

.

4

The UPS Monitoring prompt appears:

An Uninterruptible Power Supply (UPS) can be used with VCX

systems to avoid disruption due to a power outage. VCX

provides a UPS monitoring service which tracks the UPS's

status and performs a safe shutdown when the its battery is

depleted during a long power outage. To use this feature,

you must have a compatible UPS installed and configured in

accordance with the VCX documentation.

«
...
179
180
181
182
183
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Olympia Pages: 68

Brand: Yealink Pages: 6

Brand: Yealink Pages: 2

Brand: Tadiran Telecom Pages: 7

Brand: Jacob Jensen Pages: 76

RED ALERT 397-710CB

Brand: GAI-Tronics Pages: 24

Brand: Blackberry Pages: 28

Brand: Mircom Pages: 39

Brand: Paragon Pages: 80

Brand: 2N Pages: 180

Brand: M4 Pages: 19

Brand: Njoy Pages: 20

Brand: Samsung Pages: 182

Brand: Samsung Pages: 193

Brand: Samsung Pages: 2

Brand: Samsung Pages: 159

Brand: Samsung Pages: 171

Brand: Samsung Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands