3Com VCX V7000 Installation Manual Download Page 305

Page: 305 / 488

Gateway Installation

305

This command enables VLAN operation on the virtual LAN with ID = 2.

vcxSetVlanConfig 0

This command disables VLAN operation.

To verify the current settings use the

vcxShowConfig

command.

Enter this command to restart the Attendant Console:

vcxReset

This command copies the contents of the non-volatile memory to the
active network settings for the Attendant Console.

The Attendant Console communicates with the Primary VCX Server. Use
the Administrator Interface to:

■

Verify that the Attendant Console has been discovered by the VCX
system

■

Perform the remaining configuration of the Attendant Console

■

Associate the Attendant Console with a particular phone

For instructions on how to perform these tasks, see the

VCX

Administration Guide.

Gateway
Installation

3Com V7111 Analog

Gateways

V7111 Analog Gateways connect the VCX system in two directions:

■

FXO versions connect to analog trunk lines from the Public Switched
Telephone Network (PSTN).

■

FXS versions connect to analog telephones or fax machines.

There are 4-port and 8-port FXO versions of the V7111.

There are 2-port, 4-port, 8-port, and 24-port FXS versions of the V7111.

In addition, one model of the V7111 has 4 FXO ports and 4 FXS ports.

To configure any V7111 analog gateway, use a browser to connect to the
gateway. Read and follow the instructions in the

3Com VCX V7111 Fast

Track Installation Guide

Summary of Contents for VCX V7000









































































































































































































































































































































































































































































































Search results

Summary of Contents for VCX V7000

Reviews:

Brands by name

Popular brands

3Com VCX V7000, Installation Manual

Search results

Summary of Contents for VCX V7000

Reviews:

Brands by name

Popular brands