manualshive.com logo in svg

3Com Router 3000 Series, Manual, Page: 10 / 37

Share
Download
3Com Router 3000 Series Manual Download Page 10

1.1.14. Resolved Issues 

The following issues have been resolved since the release of V1.10: 

• 

A user, logging in as an operator, can no longer see administrator passwords. 

• 

RMON MIB tables cannot be created on an Ethernet interface on which RMON is 
disabled. 

• 

The RMON history bucket allocation does not fail if more than 50 buckets are 
requested. 

• 

The src and dst addresses are no longer reversed on RMON Matrix DS tables. 

• 

BRI interfaces support ISDN protocol types National ISDN and AT&T 5ESS  
(Lucent 5E). 

• 

MTU size can now be changed from the default of 1500. 

• 

Toggling route-reflection with a connection established no longer causes the router to 
reboot. 

• 

A route policy specified in a peer group now takes effect after a reboot. 

• 

When using automatic matching order with ACLs, similar rules with different 
qualifiers are added as separate rules. 

• 

Routers no longer reboot after an NBX page is completed. 

3Com Router Release Notes for V1.20

10

Summary of Contents for Router 3000 Series






































Reviews:

No comments