3Com 3Com SuperStack 3 Switch 3800 Family User Manual Download Page 60

Page: 60 / 182

4-6

HAPTER

4: C

OMMANDS

Switch 3800
Commands

The tables in this section list all of the commands used on the Switch
3800. The commands are organized by the following categories:

■

General Switch commands

■

User account commands

■

Switch management commands

■

VLAN commands

■

Protocol commands

■

FDB commands

■

Port commands

■

PACE commands

■

STP commands

■

Basic IP commands

■

Address Resolution Protocol

(ARP) commands

■

IP route table commands

■

ICMP commands

■

RIP commands

■

Logging commands

■

Configuration and image commands

unconfig switch {all}

Allows you to reset all Switch parameters (with the
exception of defined VLANs and IP addresses) to the
factory defaults. If you specify the keyword “all”, the
IP addresses are reset as well.

Table 4-3

Common Commands (continued)

Command

Description

SW3800.BK Page 6 Tuesday, May 5, 1998 5:20 PM

Summary of Contents for 3Com SuperStack 3 Switch 3800 Family























































































































































































Search results

Summary of Contents for 3Com SuperStack 3 Switch 3800 Family

Reviews:

3Com 3Com SuperStack 3 Switch 3800 Family, User Manual, Page: 60 / 182

Search results

Summary of Contents for 3Com SuperStack 3 Switch 3800 Family

Reviews: