©2020 3Built LLC
Page
1
of
9
10/5/2020
These instructions are for programming Receivers to a new Transmitter. Please be sure to read the entire instructions before programming.
Contents
Standard Transmitter
OPENING THE TRANSMITTER ........................................................................................................................ 2
PROGRAMMING TRANSMITTER TO RECEIVER .............................................................................................. 3
RESET RECEIVER ............................................................................................................................................ 4
OPTIONAL SETTINGS FOR THE RECEIVER ...................................................................................................... 5
Long Range Transmitter
OPENING THE TRANSMITTER ........................................................................................................................ 6
PROGRAMMING TRANSMITTER TO RECEIVER .............................................................................................. 7
RESET RECEIVER ............................................................................................................................................ 8
OPTIONAL SETTINGS FOR THE RECEIVER ...................................................................................................... 9
RES126VX
Receiver Programming
