2KRC Dago Red Assembly Manual Download Page 1

Page: 1 / 17

For Intermediate & Advanced Fliers.

SAFETY PRECAUTIONS

This radio control model is not a toy!

Fist-time builders should seek advice from people having building

Experience in order to assemble the model correctly and to produce

Its performance to full extent.

Assemble this kit only in places out of children’s reach!

Take enough safety precautions prior to operating this model.

You are responsible for this model’s assembly and safe operation!

Always keep this instruction manual ready at hand for quick

reference, even after completing the assembly.

Notice:

**This manual included Specification, Parts list in paper and CD full instruction manual.**

Before you read the CD. Please install Acrobat Reader. First.

“Acrobat Reader” logo are trademarks of Adobe Systems Incorporated

This Products Produce by

P & D Products Company

3F., 94 HAK PO ST., KOWLOON, HONG KONG

TEL:852 8211 2461 FAX:852 8220 6288 E-mail: [email protected] http://www.2krc.com

Sold Agent in

USA

Hobby-Lobby International

5614 Franklin Pike Circle

| Brentwood, TN 37027 USA

Phone +

(615) 373-1444

http://www.hobby-lobby.com

Summary of Contents for Dago Red


















Search results

Summary of Contents for Dago Red

Reviews:

Related manuals for Dago Red

Brands by name

Popular brands

2KRC Dago Red, Assembly Manual

Search results

Summary of Contents for Dago Red

Reviews:

Related manuals for Dago Red

Brands by name

Popular brands