247Security ZEUS Pt User Manual Download Page 20

Page: 20 / 71

247Security Inc. | 4400 North Point Parkway, Suite # 158, Alpharetta, GA 30022, USA | 1-866-693-7492 | www.247securityinc.com

USER MANUAL,

ZEUS Pt

1.6.7

BATTERY LOOPBACK PLUG

The Battery Loopback requires the Battery LoopbackPlug to enable the UPS battery feature.

One is included with each DVR. NOTE: Do not connect the Loopback plug until the DVR has been fully

installed and connected to the vehicle power source. Failure to do so can cause the on-board battery to

be drained and its capacity reduced or completely damaged.

Pins

Signal

Description

Picture

TAB-BAT1

Shorts to Pin 2

VBAT-LOOP1

Shorts to Pin 1

N/A

Not Connected

TAB-BAT2

Shorts to Pin 5

VBAT-LOOP2

Shorts to Pin 4

N/A

Not Connected

1.6.8

MINI USB CABLE

This cable connects the mDVR removable storage media to your computer or laptop for video /

audio playback. This is a standard USB 2.0 Type A to 5 Pin mini-B Cable which should be no longer than

12 to 16 inches. See section 6 for instructions on how to use the DVRViewer application to connect to

the storage media and play back your recorded video and audio.

Connector

Signal

Description

Picture

USB 2.0

Type A

Connects to your computer

USB 2.0

5 Pin mini-

Connects to the mDVR storage

media

1.7

CAMERA LENSES, WHAT VIEW, WHAT LENS

The OV360S 1.7mm camera is the standard for all applications. 0* and 15* camera lens covers

are available for exact / special positioning of cameras.

Summary of Contents for ZEUS Pt







































































Search results

Summary of Contents for ZEUS Pt

Reviews:

Brands by name

Popular brands

247Security ZEUS Pt, User Manual

Search results

Summary of Contents for ZEUS Pt

Reviews:

Brands by name

Popular brands