1010music Blackbox User Manual Download | Manualshive

Page: 9 / 106

background image

Copyright 1010music LLC 2021

Page 9 of 106

Blackbox User Manual 1.7

Output Connections

Connect speakers or headphones to the audio outputs
on the back panel. To start, we recommend connecting
external speakers or headphones to the PHONES jack,
since all outputs are routed to the PHONES jack and you
can control volume from blackbox. All of the audio jacks
are stereo 3.5mm connectors. This makes for a total of 6
audio outputs (3 Audio Out jacks x2), stereo headphones,
and a stereo input. The audio output will be at Eurorack
levels which is +/- 5 volts. This is louder than a consumer
electronics line level, so you may need a mixer to
connect with consumer electronics gear.

NOTE:

►

Not all USB power supplies are created equal. Make sure your power

supply can provide 2 amps of power. The USB power supply included

with blackbox will do this.

►

Not all USB Type B cables are the same. Some are made only for data,

while others are designed to carry power. Blackbox comes with a USB

Type B power cable. If you want to replace it with a longer cable, be

sure it is rated to carry power.

►

You can take the microSD card out and reinsert while blackbox is

powered up.

►

When you plug blackbox into a USB power bank, keep in mind that

these power banks do not send information to blackbox about how

much power is remaining. There may be a low power indicator light on

the power bank itself. Blackbox will not give you a warning when power

is low, so be sure to save your presets before the power bank runs out.

►

Some batteries may not be sufficient to support a USB MIDI device in

addition to blackbox. See

Powering MIDI Devices

below for more

information.

Back Panel

«
...
7
8
9
10
11
...
»

Summary of Contents for Blackbox











































































































Reviews:

No comments

Related manuals for Blackbox

TRAKTOR KONTROL S4

Brand: Native Instruments Pages: 85

Brand: Inter-m Pages: 19

Brand: Concept2 Pages: 48

Brand: HQ Power Pages: 47

Brand: Northern Industrial Pages: 4

Brand: Oursson Pages: 9

Brand: Sinbo Pages: 41

Brand: Monacor Pages: 22

Brand: Monacor Pages: 28

Brand: Gemini Pages: 4

Brand: Lithium Grim Pages: 10

Brand: Lithium Grim Pages: 14

JUSTIN CHANCELLOR CRY BABY

Brand: Dunlop Pages: 5

Brand: Campomatic Pages: 8

SmartMixer AT-MX341a

Brand: Audio Technica Pages: 12

Brand: ZETRON Pages: 138

MIX PRO RHMP1200 BL

Brand: Russell Hobbs Pages: 15

Brand: Russell Hobbs Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands