manualshive.com logo in svg

1010music Bitbox Micro 1.0.7, User Manual

Share
Download
1010music Bitbox Micro 1.0.7 User Manual Download Page 52

Page 52 of 88

Copyright 1010music LLC 2020

Bitbox Micro User Manual 1.0.7

Parameter

Description

Supported
Pad Modes

Root Note

When you use the Keys screen or MIDI Notes to play this sample, the
base sample will play for this root note. The sample will be pitch shifted
up or down one semi-tone for each note away from the root note. Bitbox
micro will read the root note from the WAV file if available when you add
the WAV to the preset. However, you can specify a different value here
to be used for this WAV on this pad in this preset.

If you save the WAV file from this pad, the Root Note value will be saved
with it.

Stored in the WAV smpl tag.

Sample
(Single and
Multi),
Granular

LpStr

Point where the looping will begin when playing forward, or looping will
end when playing in reverse. Expressed in samples. Must be before or
equal to LpEnd.

LpStr is read from the WAV file when sample is loaded, and saved to
the WAV file when the WAV is saved.

Stored in the WAV smpl tag.

Sample
(Single)

LpEnd

Point where the looping will end when playing forwards, or looping will
begin when playing in reverse. Expressed in samples. Must be after or
equal to LpStr.

LpEnd is read form the WAV file when a sample is loaded, and saved to
the WAV file when the WAV is saved.

Stored in the WAV smpl tag.

Sample
(Single)

BeatCount

Enter the number of beats in the clip file to give bitbox micro more
information to work with when synchronizing playback to the current
song BPM.

Stored in the WAV acid tag.

Clip

Slice Points

The slice markers that are inserted into the file. Some other software
calls these Cue Points.

Stored in the WAV cue points.

Slicer, Clip

Save and Load Parameters in WAV Files

There are several pad parameters that bitbox micro can read from and write to WAV
files. There parameters are:

Summary of Contents for Bitbox Micro 1.0.7

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands