Setting the clock
Setting the alarm
Stopping the alarm
Press and hold down the
for three seconds or longer to activate the power-saving
mode.
During the power-saving mode, the front panel display turns off. Then the
operations from the remote control, alarm function, and iPhone/iPod charge
function are disabled.
Press the
on the control panel to cancel the power-saving mode.
Press and hold down the
DIMMER/CLOCK
on the control panel for two seconds or
longer.
The time display will blink.
②
Turn the
VOLUME/CLOCK
to set to the
current time.
③
Push the
DIMMER/CLOCK
to set the time.
The time display will light up.
The display will switch between 12-hour display (12H)
and 24-hour display (24H) each time the
SNOOZE/
SLEEP
is pushed, when setting the clock’s time.
Press and hold down the
ALARM
on the
control panel for two seconds or longer.
ALARM LED and time display will blink.
Turn the
VOLUME/CLOCK
to set the
alarm time.
Push the
SNOOZE/SLEEP
.
The alarm volume display will blink.
Turn the
VOLUME/CLOCK
to adjust the
alarm volume.
Push the
ALARM
to complete the setting.
The ALARM LED and time display will light up.
Push the
SNOOZE/SLEEP
on the control
panel or remote control.
The alarm will turn off and start again in
fi
ve minutes.
• If the iPhone/iPod is connected, the beeping sound will
stop when the
SNOOZE/SLEEP
is pushed once and the
iPhone/iPod’s playback will stop when pushed twice.
• After
fi
ve minutes of stopping the iPhone/iPod’s
playback, the playback will start again with an
increasing volume, then the beeping sound will start.
• During the snooze state, the ALARM LED and POWER
LED will blink.
Push the
ALARM
on the control panel or remote
control.
• The iPhone/iPod play and beeping sound will stop, and
the alarm will turn off.
• The ALARM LED will turn off.
If the alarm is not turned off, it turns off automatically
after 60 minutes.
©2011 Yamaha Corporation
Three minutes before the alarm time, the iPhone/iPod will start playing the current song at
a low volume which will gradually increase.
When the alarm time is reached, a “beeping” sound will start.
Connect the iPhone/iPod before the set alarm time.
If an iPhone/iPod is not connected, the beeping sound will start at the alarm time.
Power on/off
DIMMER/CLOCK
• Switches the brightness of the front panel
display (Three levels)
• Sets the clock’s time
ALARM
• Switches the alarm’s
on/off status
• Sets the alarm
SNOOZE/SLEEP
Push to enable the snooze function and set
the sleep timer.
• Be sure to use a dock adaptor included your iPhone/
iPod or applicable commercially available dock
adaptor. If you do not use an adaptor or the adaptor is
not compatible, the connection may be loose or poor,
causing damage to the connector. For more information
about the dock adaptor, refer to Apple's website.
• If the iPhone/iPod is forcibly connected while still
in a protective case, the connector may be damaged.
Make sure to remove any protective iPhone/iPod case
before connecting.
• When the unit is used with the iPhone/iPod shake
shuf
fl
e function on, the iPhone/iPod might shuf
fl
e due
to the vibration of speaker depending on the music
played back. If this happens, turn the shake shuf
fl
e
function off. (Refer to the instruction manual of the iPhone/iPod to turn the function off.)
• If the iPhone/iPod is connected while playing videos or music on the iPhone/iPod, PDX-13
will turn on automatically and continue the play (except when PDX-13 is in power-saving
mode).
• You can always connect and disconnect the iPhone/iPod.
• The PDX-13’s volume level can be adjusted using the iPhone/iPod. The volume level will
also be displayed on the iPhone/ iPod.
Turning the alarm off
AUX
Within 6 m
(20 feet)
Using the sleep timer
Repeatedly press the
SNOOZE/SLEEP
on the
control panel or remote control, and select the
timer time.
• The display will alternate in the order of "30"
→
"60"
→
"90"
→
"120"
→
"current time" with each press of the
button.
• The current time will appear and the POWER LED will
blink, when the sleep timer is set.
Press the
SNOOZE/SLEEP
to disable the sleep timer
during the sleep timer is activated. The POWER LED will
turn on.
The power is turned off automatically, after the elapse of a period of time (30/60/90/120
minutes).
SNOOZE/SLEEP
ALARM
Dock adaptor
iPod dock
Printed in China
ZA31330
Portable Player Dock
PDX-13
Owner's Manual
Turning on the Power
Push the
(Power).
When the power is on, the POWER LED will light up.
Connecting Music Devices
Connect the iPhone/iPod to the iPod dock.
The battery of the connected iPhone/iPod will be charged.
Connecting an External Device
Connect to the AUX on the rear panel.
To connect an external device to PDX-13, use a
commercially available 3.5 mm (1/8 in.) stereo mini
plug cable.
Playing Audio
If you start playback on the connected device, sound will come
from the PDX-13's speaker.
iPhone/iPod's playback can be controlled using either the included
remote control or the iPhone/iPod itself.
VOLUME
FOLDER
ALARM
MENU
SNOOZE
/SLEEP
Select menu
Show iPhone/iPod's menu
Skip
Backward/Forward
Select folder
Volume control
Play/Pause
Power on/off
Alarm on/off
Push to enable the snooze
function and set the sleep timer.
Remove the insulation
sheet before using.
Operate by the
Remote control
Replacing the Battery
Pull out the battery case as
shown in the diagram below
and change a battery.
While pushing the release tab in
direction , slide out the battery
holder in direction .
Back
CR2025 button
cell battery.
VOLUME/CLOCK
Adjusts the volume/time.
Turning the alarm off temporarily (snooze function)
English
Control Panel
The current time is
displayed even when
the power is off.
SNOOZE/SLEEP
U-1
Supplied Accessories
Please con
fi
rm that the following accessories are
included before using the unit.
• Remote control • AC adaptor
Front Panel Display
Displays the current time, alarm time, and the
volume.
POWER
PM
ALARM
POWER LED
Lights up when the PDX-13’s power is turned on.
Blinks when the sleep timer is set.
PM LED
When displaying the time with the 12-hour display, stays off during
the a.m. hours and lights up during the p.m. hours.
ALARM LED
Lights up when the alarm is set.
Multi-Source Mix
When an iPhone/iPod and another external device
are connected to PDX-13, audio can be enjoyed in
many ways—for example, by playing music while
listening to the news.
Integrated Volume Control
You can control the PDX-13's volume level by
operating the volume control function on the
iPhone/iPod.
Charge Your iPhone/iPod Battery
Alarm Function
Use the alarm function to wake up to music from
your iPhone or iPod.
Features
Before Use
Connect the included AC adaptor.
Connect the AC adaptor to PDX-13, before
connecting the power cable to the wall outlet.
12V ---
①
②
