background image

HEAT PUMP INSTALLATION INSTRUCTIONS

HEAT PUMP SAFETY

Table of Contents

HEAT PUMP SAFETY.....................................................................1

INSTALLATION REQUIREMENTS ................................................2

Tools and Parts ............................................................................2
System Requirements..................................................................2
Location Requirements ................................................................2
Electrical Requirements ...............................................................3

INSTALLATION INSTRUCTIONS ..................................................4

Inspect Shipment .........................................................................4

Connect Refrigerant Lines ...........................................................4
Make Electrical Connections .......................................................5
Complete Installation....................................................................7
Sequence of Operation ................................................................7

SYSTEM MAINTENANCE ..............................................................9

ASSISTANCE OR SERVICE ...........................................................9

Accessories ..................................................................................9

WARRANTY ..................................................................................11

Whirlpool Gold

 Model W2GH3

48348M005

You can be killed or seriously injured if you don't immediately 
 

You

 

can be killed or seriously injured if you don't follow 

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 
messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Summary of Contents for W2GH3













Reviews: