CLVD1325/5-50
Order number
2GF1667-8AU
Document
A6V10062007
Edition
02.2007
Installation Instructions
English
INTRODUCTION
Thank you for purchasing this Siemens product. Please read and follow
these instructions carefully.
MOUNT TYPE
This lens is designed for use with 1/2 inch C-mount CCD cameras
(17.526mm flange dimension). When fitting the lens to a CS-mount
camera, an adapter ring must be used to ensure correct flange position
(supplied free of charge with all Siemens cameras).
MOUNTING TO THE CAMERA
The lens is installed by screwing it clockwise into the mount on the CCTV
camera. Having screwed the lens in as far as it will go, you can rotate the
lens chassis back to suit the setup position of the camera.
IRIS
If the camera is fitted with a selection switch for Video and DC, set it to
DC.
TO INSURE LONG-TERM RELIABILITY
Remove dust from the lens using a blower or soft brush. Avoid touching the
lens surface.
Use lens cleaning paper or a clean cotton cloth with a little cleaning liquid to
remove finger prints or oil stains from the lens surface. Start in the centre of
the lens and work outwards. Avoid using organic solvents such as thinner or
benzene.
SPECIFICATION
Imager Size
1/3 inch
Focal Length
5-50 mm
Aperture Range
DC IRIS
F 1.4 – 360
TELE WIDE
Angle of View
Horizontal
Vertical
5,6
°
4,2
°
53,6
°
40,3°
Mount-Type CS-Mount
Application Temperature Range
-10 - +60°C
Minimum Object Distance
0,3 m
PRODUCT SAFTY PRECAUTIONS
The following symbols appear in these safety instructions.
Ꮨ
This symbol indicates presents of an electrical current and the
risk of electric shocks.
Ꮬ
This symbol means that you should not disassemble the
product.
This symbol indicates a risk of fire.
This symbol means that you must comply with the instruction
concerned.
HAZARD
Serious injury or loss of life may result from failure to comply with safety instructions in this category.
ᏜᏘ
Do not scratch, cut open, twist or heat
the connection cable.
ᏜᏘ
Do not disassemble the unit or try to
insert metal objects or flammable materials into it.
Ꮨ
Do not attempt to use the product if you
see smoke or smell burning.
ᏜᏘ
If the connection cable is cracked or
damaged, switch off immediately.
Ꮨ
Do not expose the unit to water. If
water should penetrate the unit, switch off
immediately.
Do not look into the sun through the
lens as this could cause blindness.
Do not place the unit near extreme heat,
an open flame or a source of flammable gases.
ᏜᏘ
Do not try to repair the unit or the
power supply
Keep the product out of children's
reach. If the product were to fall on a child, it
could cause serious injury.
Ꮨ
Do not plug in or unplug the cable with
wet hands
Do not expose the product to extremely
high or low temperatures. (not hotter than +60°C
or colder than -10°C). Extreme temperatures will
affect performance and may damage the product.
Ꮨ
Keep the connection cable away from
heat sources as these could melt the insulation.
Ꮨ
Do not place the product near a stove
or humidifier or in any other location where there
are conditions of high heat or humidity.
If you intend to connect the product to
another product, read the connection instructions
in both product manuals carefully beforehand.
Do not store a lens in direct sunlight.
Light passing through the lens could cause a fire
if directed at a flammable material.
Do not drop the product or expose it to
heavy impacts. This could lead to serious
damage.
Front View
D1 32 mm
D2 24,6
mm
Pin out connections
(Camera socket viewed from
above)
Pin Function
1
Control - Orange
2 Control
+
Yellow
3
Red
4
Driver -
Black
Side View
D1 40 mm
D2 38,6
mm
L 59,2
mm
A 4,0
mm
