Sharp WH-237DP User Manual Download

Page: 1 / 21

SHARP SERVICE MANUAL

ELECTRIC WATER HEATER

MODELS

WH-237DP
WH-247D

SHARP CORPORATION

TABLE OF CONTENTS

PARTS IDENTIFICATION AND SPECIFIC INFORMATION ..............................................

EXTERNAL DIMENSION ...................................................................................................

CAUTION FOR USE ..........................................................................................................

HOW TO USE ....................................................................................................................

WIRING DIAGRAM ............................................................................................................

INSTALLATION ADVICE ....................................................................................................

ELECTRIC WIRE CONNECTIONS ....................................................................................

SHOWER SET ....................................................................................................................

REPLACING METHOD FOR MAIN PARTS .......................................................................

TROUBLESHOOTING .......................................................................................................

CIRCUIT DIAGRAM (PCB-A) .............................................................................................

SERVICE PARTS LIST .......................................................................................................

Page

5-8

8-10

11-16

19-21

In the interests of user-safety (Required by safety

regulations in some countries) the set should be restore

to its original condition and only parts identical to those

specifi ed should be used.

Summary of Contents for WH-237DP






















Search results

Summary of Contents for WH-237DP

Reviews:

Related manuals for WH-237DP

Brands by name

Popular brands

Sharp WH-237DP, Service Manual

Search results

Summary of Contents for WH-237DP

Reviews:

Related manuals for WH-237DP

Brands by name

Popular brands