background image

 

Philips Lighting North America Corporation 
200 Franklin Square Drive 
Somerset, NJ  08873, USA 
Phone:  855-486-2216 

www.philips.com/luminaires

  

Philips Lighting Canada Ltd. 
281 Hillmount Road, 
Markham ON, Canada  L6C 2S3 
Phone:  800-668-9008 

www.philips.com/luminaires

 

9140053550 February 2016 

 

 

 

 
 

Symmetry Cast 
Aluminum Exit 

230 VOLT 50Hz 

 

Service Questions Call: 910-259-1000 

 

INSTALLATION AND 

OPERATING 

INSTRUCTIONS 

 

 

 
 
 
 
 
 
 
 

 

IMPORTANT 

SAFEGUARDS 

 
When  using  electrical  equipment,  basic  safety 
precautions  should  always  be  followed,  including 
the following: 

 

READ AND FOLLOW ALL 

SAFETY INSTRUCTIONS 

 

All  servicing  should  be  performed  by  qualified 
personnel only. 
 
Equipment  should  be  mounted  in  locations  and  at 
heights  where  it  will  not  be  readily  subjected  to 
tampering by unauthorized personnel. 
 
The  use  of  accessory  equipment  not  recommended 
by the manufacturer may cause an unsafe condition. 
 
Do  not  use  this  equipment  for  other  than  intended 
use. 
Do not use outdoors. 

 
Do not let supply cords touch hot surfaces. 
 
Do not mount near gas or electric heaters. 
 
Use  caution  when  servicing  batteries.  Battery  acid 
can  cause  burns  to  skin  and  eyes.  If  acid  is  spilled 
on  skin  or  eyes,  flush  acid  with  fresh  water  and 
contact a physician immediately. 
 

SAVE THESE 

INSTRUCTIONS 

 

WARNING – Shut off AC power to branch circuits 
to which units will be connected. All wiring should 
be per N.E.C. Articles 501-4(b) and local codes. 
 
To  maintain  warranty,  equipment  with  batteries 
must  be  installed  or  placed  on  charge  within 
prescribed period after shipment. 

 

 
 

 

 

Summary of Contents for SC Series









Reviews: