Operating Instructions
Replacement lamp unit
for DLP
®
Projectors
Model No.
ET-LAD12K (1 pc)
ET-LAD12KF (4 pcs)
Read these instructions completely before operating this unit.
Information for Users on Collection and Disposal of Old Equipment and used Batteries
Commercial Use
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/
EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your
local municipality, your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact
your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
LAD12000_eng_080715.fm 1 ページ 2008年9月10日 水曜日 午後1時29分
4
4)
取り換えたいランプユニット固定ねじ
(各 3 本)をプラスドライバーで取り
外し、ランプユニットの取っ手を
持って、ゆっくりと本機から引き出す
5)
新しいランプユニットを挿入方向に注意して押し込む
挿入時、特に
部と
部をよく押し込んでください。
6)
ランプユニット固定ねじ(各 3 本)をプラスドライバーでしっかりと締めつける
7)
ロックレバーを元に戻し、ランプユニット
収納カバーを閉め、ランプユニット収納
カバー固定ねじ(1 本)をプラスドライバー
でしっかり締めつける
8)
プロジェクター取扱説明書の「エアーフィルターの清掃と交換」の手順を守り、エアー
フィルター内の古い静電メッシュフィルターを同梱の新しい静電メッシュフィルターに
交換してください。
同時にエアーフィルター(フィルタークリーニングユニット、可動式金属メッシュフィ
ルタ、ブラシ)を清掃してください。
静電メッシュフィルター
付属品
取っ手
ランプユニット2
ランプユニット1
ランプユニット3
ランプユニット4
ランプユニット固定ねじ
使用直後のランプユニットおよび
ランプユニット周辺の構造物は
高温なので注意する
・触るとやけどの原因になります。
高温注意
注 意
ランプユニット収納カバー固定ねじ
ランプユニット収納カバー
ランプユニットやランプユニット収納カバーは
確実に取り付けてください。ランプユニットや
ランプユニット収納カバーの取り付けが不完全
ですと保護回路が動作し電源が入りません。
S0808-1098B
LAD12000_JP_080715.fm 4 ページ 2008年9月10日 水曜日 午後1時27分
S0808-3020D