Additional Information
For detailed information on setting up and using the
Scanning and Scanning/MSR module, refer to the
ET1 Enterprise Tablet User Guide
and
Integrator
Guide
.
Regulatory Information
This device is approved under Motorola Solutions,
Inc.
This guide applies to the following model numbers:
SCANMOD-ET1 and MSRSCAN-ET1.
All Motorola devices are designed to be compliant
with rules and regulations in locations they are sold
and will be labeled as required.
Local language translations are available at the
following website:
http://supportcentral.motorola.com.
Any changes or modifications to Motorola
equipment, not expressly approved by Motorola/
Symbol Technologies could void the user’s authority
to operate the equipment.
For use only with Motorola approved and UL Listed
mobile computers. Motorola approved and UL Listed
accessories and/or Motorola approved and UL
Listed/Recognized battery packs.
Declared maximum operating temperature: 50 °C.
Health and Safety
Recommendations
Ergonomic Recommendations
•
Reduce or eliminate repetitive motion
•
Maintain a neutral postures
•
Reduce or eliminate excessive force
•
Keep objects that are used frequently within easy
reach
•
Perform tasks at correct heights
•
Reduce or eliminate vibration
•
Reduce or eliminate direct pressure
•
Provide adjustable workstations
•
Provide adequate clearance
•
Provide a suitable working environment
•
Improve work procedures
Class 2 laser scanners use a low power, visible light
diode. As with any very bright light source, such as
the sun, the user should avoid staring directly into
the light beam. Momentary exposure to a Class 2
laser is not known to be harmful.
CAUTION:
Use of controls, adjustments or
performance of procedures other than those
specified herein may result in hazardous laser light
exposure.
Labeling
Label read:
1. CAUTION - CLASS 2 LASER LIGHT WHEN
OPEN. DO NOT STARE INTO BEAM.
2. COMPLIES WITH 21CFR1040.10 AND 1040.11
EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE NO. 50, DATED JUNE 24, 2007
AND IEC 60825-1 (Ed.1.2, 2.0); EN60825-
1:2001, 2007 & IEC62471 (Ed.1.0);
EN62471:2008.
3. LASER LIGHT - DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT.
Radio Frequency Interference
Requirements-FCC
Note: This equipment has been
tested and found to comply with
the limits for a Class B digital
device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment
and receiver
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected
•
Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
In order to avoid or minimize the
potential risk of ergonomic injury
follow the recommendations below.
Consult with your local Health &
Safety Manager to ensure that you
are adhering to your company’s
safety programs to prevent
employee injury.
Laser Devices
CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT
STARE INTO THE BEAM. ATTENTION- LUMIÉRE LASER DE
CLASSE 2 EN CAS D'OUVERTURE. NE PAS REGARDER
DANS LE FAISCEAU.VORSICHT- LASERLICHT KLASSE 2,
WENN ABDECKUNG GEÖFFNET. NICHT IN DEN STRAHL
BLICKEN.
⊼ᛣ˖ᠧᓔᯊঞ㘨䫕༅ᬜᯊ᳝▔ܝ䕤ᇘ࣓Ⳉ㾚ܝᴳ
COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR
DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED
JUNE 24, 2007 AND IEC 60825-1 (Ed.2.0),EN60825-1:2007 &
IEC62471:2006 (Ed. 1.0) EN62471:2008.
LASER LIGHT- DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT. LASERLICHT - NICHT
IN DEN STRAHL BLICKEN. LASER KLASSE 2.
LUMIÈRE LASER - NE PAS REGARDER DANS
LE FAISCEAU. APPAREIL À LASER DE
CLASSE 2 630-680nm, 1mW
▔ܝ䕤ᇘ࣓Ⳉ㾚ܝᴳ㉏▔ܝѻક
3
2
1
Data Capture
7. Secure the two screws using a
T8 Torx screwdriver.
8. Replace the battery.
5. Remove the existing module. Do
not remove filler plate.
6. Install the new module.
1. Power off the ET1.
2. Remove the battery.
3. If the handstrap is installed,
rotate the handstrap to access
the expansion module screws.
4. Remove two screws using a T8
Torx
®
screwdriver.
Installation
MSR Swipe
Filler Plate
