OVERVIEW
The Motorola DRC450 universal remote
will control up to four devices, including
Motorola's interactive digital terminals*,
most TVs,VCRs,Amplifiers, DVD players,
PVRs, Tuners, and CD players.
*NOTE: Digital models include the DCT1000,
DCT1200, DCT1700, DCT2000, DCT2500, and
DCT5100. The DRC450 can also control older
Motorola analog models like the CT1900,
CFT2100, CFT2200, and CFT3300.
The DRC450 requires two new AA
alkaline batteries (included) and has
easy programming to control your
Motorola interactive digital terminal, as
well as all of the basic functions of your
other original remote controls. Moreover,
the DRC450 helps eliminate the need to
use multiple remote controls.
For best results, please read and perform
all instructions listed herein.Also, keep
these instructions for future reference.
FEATURES AND FUNCTIONS
Use the DRC450 mode keys (i.e.,
AUDIO
,
VCR/DVD
,
CABLE
, or
TV
) to control a
specific device.When pressed, the
selected mode key will light, confirming
your choice. Use the other keys to per-
form desired actions (see the following
key chart).
NOTE: The selected mode will remain active
until you press another mode key.
Press
AUDIO
,
VCR/DVD
,
CABLE
, or
TV
once to
control a device.
Press
POWER
once to
turn on or off the
selected home enter-
tainment device.
Press
HELP
once to
display the help screen.
Press
MUTE
once to
turn sound off or on.
Use
PAGE
▲
(or
PAGE
▼
)
to page up (or down)
through menu screens
and the electronic
program guide.
Use
LOCK**
to restrict
viewing of selected
programs (Parental
Control).
Use
EXIT
to exit menu
or guide.
Use
INFO
to display
current channel and
program information.
Use these keys to move
the cursor in the elec-
tronic program guide
and menu screens.
Use
OK**
to chose menu
options, PPV events,
and to tune programs
from the electronic
program guide.
Use
GUIDE
to display
the electronic program
guide.
Use
MENU
to display
the main menu.
In
TV
or
CABLE
mode,
use
(or
VOLUME -
) to raise (or
lower) sound volume.
Use
C
(or
CHANNEL -
) to select
the next higher (or
lower) channel.
Use
LAST
to recall last
channel or go back one
screen in the menu.
In the
CABLE
mode,
press
FAVORITE
once
to display programmed
favorite cable channels.
These functions are
set by your cable
system operator.
Use the keypad (
0
~
9
)
to directly select the
channels (e.g., 09 or
031).
Press
TV/VCR BYPASS
once to switch VCR to
view TV or tape (not
supported by all
applications).
Use
ENTER/MUSIC
to
display menu of digital
music channels, or to
enter channels on
some TV models.
In the
VCR/DVD
and
TV
modes, use the
STOP
,
PAUSE
,
PLAY
,
REW.
,
and
F.FWD.
keys to
control a VCR (or DVD
player). To record
a program on a VCR,
press
RECORD
once.
In the
CABLE
mode,
press
DAY>
(or
<DAY
)
once to move the
electronic program
guide ahead (or back)
24 hours.
**NOTE: Functionality of the
LOCK
and
OK
keys are dependent on the software and the
model of Motorola interactive digital terminal.
INSTALLING BATTERIES
1.
On the DRC450’s back, pull back
the battery cover and remove it.
2.
Use the two (2) supplied fully-
charged AA alkaline batteries.
Match their + and - marks to the
+ and - marks in the battery case,
then insert the batteries.
3.
Push the battery cover back
into place.
4.
Test the unit by pressing
POWER
and any mode key (e.g.,
AUDIO
,
VCR/DVD
,
CABLE
, or
TV
). If the
batteries are inserted correctly, the
selected mode key will be lit.
NOTE: When a selected mode key blinks two
times with each key press, this indicates that
the batteries are getting low. Replace them
within 20 minutes; otherwise the DRC450 may
lose its settings and require reprogramming.
PROGRAMMING A SPECIFIC
DEVICE CONTROL
The DRC450 is preprogrammed at the
factory to operate a RCA TV and VCR
(or DVD player), a Motorola (General
Instrument) interactive digital terminal,
and a Pioneer audio device. To control
devices other than the default brands,
perform the following steps; otherwise
skip this section:
NOTE: For programming TV/VCR Combo
control, see the next section.
1.
Turn on a device (e.g.,VCR) and, if
applicable, insert media, (e.g.,
cassette or disc).
NOTE: Please read steps 2-4 completely
before proceeding. Highlight or write
down the codes and device you wish to
program before moving on to step 2.
2.
On the DRC450, press and hold a
mode key (i.e.,
AUDIO
,
VCR/DVD
,
CABLE
, or
TV
) for at least 6 seconds,
until you see the programming
mode start. Each mode key light
will turn off and on sequentially,
starting with
AUDIO
on through
TV
,
and the sequence will repeat twice.
At this time, release the mode key
and wait until it’s lit continuously.
3.
Locate the code for your device in
Manufacturer’s Codes
on the back
of this user guide. Brands are listed
in alphabetical order with the most
popular codes listed first.
4.
Enter the first four-digit code for
your device. If you perform this
procedure correctly, the selected
mode key will blink three times.
NOTE: If you enter an invalid code, the
selected mode key will turn off. Repeat
steps 2 through 4 with a valid code.
5.
Aim the DRC450 at your device
and press
POWER
once. The device
should turn off. If it does not
respond, repeat steps 2-4, trying
each code listed for your brand
until you find one that works. If it
still does not work, try
Searching
For Your Code
.
NOTE: If the device does not have a
POWER
key, press the
(
Play
) key.
6.
For future reference, write your
device code in the appropriate
boxes below:
AUDIO Code:
Device Type:______________
VCR/DVD Code:
Device Type:______________
CABLE Code:
TV Code:
7.
Repeat steps 1 through 6 for each
device you want to control.
PROGRAMMING
TV/VCR COMBO CONTROL
1.
Turn on the TV/VCR Combo and
insert a video cassette.
NOTE: Please read steps 2-4 completely
before proceeding. Highlight or write
down the codes and device you wish to
program before moving on to step 2.
2.
On the DRC450, press and hold a
VCR/DVD
for at least 6 seconds,
until you see the programming
mode start. Each mode key light
will turn off and on sequentially,
starting with
AUDIO
on through
TV
,
and the sequence will repeat twice.
At this time, release
VCR/DVD
and
wait until it’s lit continuously.
3.
Locate the code for your device in
Setup Codes For TV/VCR Combos
on the back. Brands are listed in
alphabetical order with the most
popular codes listed first.
4.
Enter the first four-digit code for
your device. If you perform this
procedure correctly,
VCR/DVD
will
blink three times.
NOTE: If you enter an invalid code,
VCR/DVD
will turn off. Repeat steps 2
through 4 with a valid code.
5.
Aim the DRC450 at the TV/VCR
combo and press
POWER
once.
The device should turn off. If it
does not respond, repeat steps 2-4,
trying each code listed for your
brand until you find one that
works. If it still does not work, try
Searching For Your Code
.
NOTE: If the device does not have a
POWER
key, press the
(
Play
) key.
NOTE: If you’ve located a TV/VCR code
that works, but it has a separate TV
code, you’ll also need to program it into
DRC450 to access volume control.
Perform the steps in “Programming
Device Control” and use
TV
for the mode
key (e.g., press and hold
TV
).
6.
For future reference, write your
device codes in the boxes below:
TV/VCR Combo Code:
TV Code (if used):
SEARCHING FOR YOUR CODE
If your home entertainement device does
not respond to the DRC450 after trying
all of the codes listed for your brand, or
if your brand is not listed at all, try
searching for your code.
For example, after trying all of the codes
for your TV, you still cannot get the
DRC450 to operate your TV, then:
1.
Turn on your TV.
2.
On the DRC450, press and hold
TV
(at least 6 seconds) until you see
the programming mode start. Each
of the mode key lights will turn off
and on sequentially, starting with
AUDIO
on through
TV
, and the
sequence will repeat twice. During
this time, release
TV
and wait until
it’s lit continuously.
3.
Press the (
Up
) cursor key once
to start the search mode.
NOTE: In the search mode, the DRC450
will send IR codes from its library to the
selected component, starting with the
most popular codes first. When the
device responds to a subsequent key
command (e.g.,
POWER
), the correct
device code will be found.
4.
Press
POWER
once. The
TV
key will
light on and off, showing that an
IR code has been sent.
5.
If your television does not turn off,
press the (
Up
) cursor key once
again to call up the next IR code
and press
POWER
once again.
6.
If your television still does not
turn off, repeat step 5 as many
times as needed until your TV
turns off.
7.
When your television does turn off,
a working code has been found.
Press
OK
once to save the code and
the
TV
key will blink three times,
confirming the selection.
8.
To search for the codes of your
other devices, repeat steps 1
through 7, but substitute the
appropriate mode key (i.e.,
VCR/DVD
,
CABLE,
or
AUDIO
) for the
device you are searching for.
CHECKING THE CODES
If you have set up the DRC450 using the
Searching For Your Code
procedure, you
may need to find out which four-digit
code is operating your equipment.
Perform the following procedure after
you have set up your devices to find out
which four-digit code is operating your
equipment. For example, to find out
which code is operating your TV:
1.
Turn on your TV.
2.
On the DRC450, press and hold
TV
(at least 6 seconds) until you see
the mode light sequence start.
Each of the mode key lights will
turn off and on sequentially, start-
ing with
AUDIO
on through
TV
, and
will repeat twice. During the
sequence, release the
TV
key and
wait until it stays lit continually.
3.
Press
9
-
9
-
0
. The
TV
key will
blink three times.
4.
To view the code for the first digit,
press and release
1
. Count the
number of
TV
key blinks (e.g., 3
blinks = 3) and write down the
number in the leftmost TV code
box in step 6 of
Programming
Device Control
.
NOTE: The mode key will not blink if
the code digit is a “0”.
5.
Repeat step 4 three more times for
each successive digit by pressing
and releasing
2
,
3
, and then
4
.
Finish writing down the TV code
in the remaining TV code boxes.
6.
To check for the codes of your
other devices, repeat steps 1
through 5, only substitute the
appropriate mode key (i.e.,
VCR/DVD
,
CABLE,
or
AUDIO
) for the
device you are checking.Write
down the codes in the appropriate
device code boxes (see step 6 of
Programming Device Control
).
CHANGING VOLUME LOCK
Your new DRC450 is set to control the
volume of a device through its associated
mode (i.e., through the
Motorola
interactive digital terminal
in the Cable
mode, through the
TV
in the TV mode,
through the
VCR
or
DVD player
in the
VCR/DVD mode, and through the
audio
device
in the Audio mode). If your TV is
not remote controllable, or if you would
like the volume to be controlled by a dif-
ferent device, you can change the Volume
Lock setting to control a volume through
a non-associated mode (e.g., through
the
Motorola interactive digital terminal
in the TV mode).
Changing the Volume Lock setting to
the Cable,VCR/DVD, or TV mode will
change the volume control for all modes
except Audio, which will continue to
control its own volume. If you change
the Volume Lock setting to the Audio
mode, all modes (i.e.,Audio., Cable,
VCR/DVD, and TV) will be controlled by
the Audio mode.
To Change The Volume Lock Setting
To Another Mode:
1.
On the DRC450, press and hold a
mode key (i.e.,
AUDIO
,
VCR/DVD
,
CABLE
, or
TV
) for at least 6 seconds,
until you see the programming
mode start. Each mode key light
will turn off and on sequentially,
starting with
AUDIO
on through
TV
,
and the sequence will repeat twice.
At this time, release the mode key
and wait until it’s lit continuously.
2.
Press and release
.
3.
The mode key’s light will blink
three times, indicating volume has
been locked to the selected mode.
4.
Now, whenever you press
,
VOLUME -
, or
MUTE
on the DRC450, volume will be
controlled by selected mode,
independent of the current mode.
To Unlock Volume Lock:
1.
On the DRC450, press and hold a
mode key (at least 6 seconds) until
you see the programming mode
start. Each mode key light will turn
off and on sequentially, starting
with
AUDIO
on through
TV
, and the
sequence will repeat twice. During
this time, release the mode key and
wait until it’s lit continuously.
2.
Press and release
VOLUME -
.
3.
The mode key light will blink three
times, indicating volume has been
unlocked for the selected mode.
4.
Now, whenever you press
,
VOLUME -
, or
MUTE
on
the DRC450, the volume controls
will reset to their original device.
TROUBLESHOOTING
PROBLEM:
A mode key does not
blink or blinks 2 times
when you press a key.
SOLUTION: Replace the batteries with
two (2) new AA alkaline
batteries.
PROBLEM:
A mode key blinks when
you press a key, but home
entertainment component
does not respond.
SOLUTION: Make sure the DRC450 is
aimed at your home
entertainment device
and is not farther than
15 feet away.
continued on back...
Fold
Fold
F
old
F
old
F
old
F
old
F
old
F
old
F
old
F
old
F
old
F
old
F
old
F
old
F
old
F
old
DRC450
UNIVERSAL REMOTE CONTROL
MADE IN INDONESIA
USER GUIDE
Moto DRC450_Mnl 10/2/02 12:04 PM Page 1
