background image

GAS COOKTOP 

To contact LG Electronics, 24 hours a day, 
7 days a week: 

1-800-243-0000 (U.S.A.) 
 1-888-542-2623 (Canada) 

 

Or visit us on the Web at:  

us.lge.com (U.S.A.) 
ca.lge.com (Canada) 

INSTALLATION INSTRUCTIONS 

Please read this guide thoroughly 

before installation. 

BEFORE YOU BEGIN 

Read these instructions completely  
and carefully. 

Installation of this cooktop must conform with local 
codes, or in the absence of local codes, with the 
National Fuel Gas Code, ANSI Z223.1/NFPA.54, 
latest edition. In Canada, installation must 
conform with the current Natural Gas Installation 
Code, CAN/CGAB149.1 or the current Propane 
Installation Code, CAN/CGA-B149.2, and with 
local codes where applicable. This cooktop has 
been design-certified by CSA International 
according to ANSI Z21.1, latest edition and 
Canadian Gas Association according to 
CAN/CGA-1.1 latest edition. 

As with any appliance using gas and generating 
heat, there are certain safety precautions you 
should follow. You will find these precautions in 
the Important Safety Information section in your 
User’s Guide. Read them carefully. 

• IMPORTANT 

– Save these instructions 

for local electrical inspector’s use. 

• IMPORTANT 

– Observe all governing 

codes and ordinances. 

P/No.: MFL62725501

Note to Installer: 

Leave these instructions with 

the appliance after installation is completed. 

Note to Consumer:  

Keep the User’s Guide and 

Installation Instructions for future reference. 

NOTE: This appliance must be properly 
grounded. 

•  

The electrical diagram is in an envelope 
attached to the back of the cooktop. 

•  

Skill level – Installation of this appliance 
requires basic mechanical skills. 

•  

Proper installation is the responsibility of the 
installer. 

•  

Product failure due to improper installation is 
not covered under the Warranty. 

•  

Remove all tape and packaging. 

•  

Make sure the burners are properly seated 
and level. 

•  

Take the accessory pack off of the cooktop. 

•  

Check to be sure that no cooktop parts have 
come loose during shipping. 

Summary of Contents for Gas Cooktop
















Reviews: